Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
so with one of described pins disconnected power-on then 3 sec wait then connect wire, tv starts with perfect picture, was working for whole day no issues, will try 1Mo resistance yesterday, and delay switch ordered, probably would take few weeks to come. I could not find any shorts tried tape method on all pins, only those I described prevent power cycling
-
I tried that, works as expected, tried resistance from 0-50Kohm, do you think it may need some higher resistance?...Last edited by xfox; 12-20-2023, 08:49 PM.
Leave a comment:
-
Tried everything... And I got one idea... what if I'll put some delay switch like this [url]https://www.aliexpress.us/item/3256805559478462.html?spm=a2g0o.productlist.main.39.15884cc7Blq37a&algo_pvid=9310aab1-673e-4637-b820-21251a36c7c4&aem_p4p_detail=2023122013294214477768452240100001074166&algo_exp_id=9310aab1-673e-4637-b820-21251a36c7c4-19&pdp_npi=4%40dis%21USD%213.99%213.75%21%21%213.99%21%21%402103241d17031077825448802e7543%2112000034195967861%21sea%21US%21125539771%21&curPageLogUid=uBGcaHbMkdhX&search_p4p_id=2023122013294214477768452240100001074166_4[/url]Tried everything...Last edited by xfox; 12-20-2023, 03:31 PM.
Leave a comment:
-
Just tried, was not able to get a picture but if I cover one of pins, TV is not restarting so if you look at main board top ribbon (right on LCD) second or one before last, and on lower ribbon (left on LCD) first and last, covering any of those pins will get tv of power cycling but there is no picture.
-
Re: Samsung smart tv bad power board BN44-0503A
ok, so with pull up resistor voltage is 12.75 13.3 and 13.4
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
[ATTACH]239450[/ATTACH]
Voltage on picture, so it's switching from one to another, looks like main board is trying to reset itselfRe: Samsung smart tv bad power board BN44-0503A
[ATTACH]239450[/ATTACH]
Voltage on picture, so it's switching from one to another, looks like main board is trying to reset itself...
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
Oh, sorry... So voltage is 13.25V without main board connected and switching from 13.25 to 19v with main boardLast edited by xfox; 06-22-2021, 01:12 PM.
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
Marked ground on attached photo with blue
[ATTACH]239380[/ATTACH]...
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
Tried disconnecting, same measurements
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
CP814S - 163v
CS805 - switching from 14v to around 19.5v
QS801 - same as CP814 163v
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
Nothing on main capacitor, all looks ok
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
So what I did, I replaced resistors RP810 and RP810 and QP801S, after that board not exploded and LED light started to blink (5 times double blinks), nothing on backlights connector (0V), checked backlight with LED tester, looks good and working
mainboard connector:
PIN14 (Power On_off): 3,2V
PIN12 (A5V): 5V
CP818 and CP819 - no short
DP802, DP803, DP808 - no short, reverse ok
BD801S no short, shows 0.555 one way only (soldered)
ICP801S - not sure how to check
PIN6 - PIN7...
Leave a comment:
-
Re: Samsung smart tv bad power board BN44-0503A
Looks like also burned two resistors one RP810 (68 Ohm) and RP809 (30 Ohm)...Last edited by xfox; 06-14-2021, 10:57 PM.
Leave a comment:
-
Samsung smart tv bad power board BN44-0503A
Hello, got Samsung smart tv with bad power board BN44-00503A, diagnosed bad MOSFET F13NM60N (QP801S) and 5A fuse, after replacing both, replaced mosfet burned out immediately, fuse is ok, maybe somebody knows what can be checked prior trying one more?
[ATTACH]238904[/ATTACH]
[ATTACH]238905[/ATTACH]Hello, got Samsung smart tv with bad power board BN44-00503A, diagnosed bad MOSFET F13NM60N (QP801S) and 5A fuse, after replacing both, replaced mosfet burned out immediately, fuse is ok, maybe somebody knows what can be checked prior trying one more?
[ATTACH]238904[/ATTACH]
...Last edited by xfox; 06-14-2021, 10:40 PM.
-
Re: Vizio M65-C1 no picture
Universaly, yeah picture is perfect, but not background, I think it's because without spi flash VGH is pulsingLast edited by xfox; 11-05-2020, 11:09 AM.
Leave a comment:
No activity results to display
Show More
Leave a comment: