Just a quick note to say my original issue with the HP G7000 was resolved by fitting those new parts.
Thanks for all your help
fusionmax
Member
Last Activity: 01-17-2013, 11:39 AM
Joined: 09-05-2010
Location:
-
Re: HP G7000 Dead
Just a quick note to say my original issue with the HP G7000 was resolved by fitting those new parts.
Thanks for all your help
-
Re: HP G7000 Dead
Thanks for the suggestion, I spotted the guy in Portugal selling them and have ordered a couple.
Ill report back when I get them and fit them with the results
Leave a comment:
-
Re: HP G7000 Dead
Any idea where I can get replacements in the UK??Leave a comment:
-
Re: HP G7000 Dead
I have found what I think are the equivalent parts on the mobo. I have attached a picture.
The parts are labeled...
AH5AJ
FDS
6675BZ
Am i looking at the right thing?
EDIT : I have also found a datasheet and am now pretty sure I am looking at the right thing.
Any tips on how to test them?...Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
That reply has prompted me to dig the monitor back out of the cupboard and give things another go!Leave a comment:
-
HP G7000 Dead
Hi all,
I have a HP G7000 laptop here that is totally dead. Pressing the power button gives me nothing, connecting the AC adapter gives me nothing. No lights or anything.
I have stripped the laptop and checked for anything obvious, I have also checked the solder joints on the mainboard and confirmed the power adapter is supplying the required 19.5v.
Can anyone advise me on my next move? -
Re: Yusmart 229IP-P 22" LCD Monitor Dead
I think this monitor might be destined for the bin! I am not getting anywhere and the thread has gone all quiet.
Quotidian, did you ever get anywhere with yours?Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
I have still not managed to make any progress with the monitor
I think we were looking at the reset controller but with PlainBills comment....
I assume the board doesnt look like it has one?...Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
No, it is a damaged board. A few of them have been smashed off so I was planning on just replacing them with a jumper.
It is only a control panel so hopefully there should be no RF issues
Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
Thanks for that, I assume I could replace them with a jumper wire without any issues?Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
Completely unrelated I know but just on the off hand...... can anybody identify the component in the image below for me?
It only has a marking of 0, is it a smd capacitor?...Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
I'm starting to think this might be a lost cause
Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
I have sccanned the board and listed the SOT-23 package chipsets that I can see....
I have been trying to identify them from what little info they have on the chips but haven't been very successful so far...Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
Hate to be a bumper but has anyone got any ideas?
I am at a loss!Leave a comment:
-
Re: ASRock k7s41gx
Maybe 15mm was a bit out, I was trying to measure the diameter with a tape measure. On a second look maybe 10mm is more accurate
I have attached a couple of pics.............Last edited by fusionmax; 10-09-2010, 05:35 AM.Leave a comment:
-
ASRock k7s41gx
I have just recieved this board as a possible replacement for a blown board in my home server, but it has loads of bloated caps
I am going to try replacing them all but wondered if anyone could suggest some suitiable replacements? The spec are as follows.....
20mm high
About 15mm diameter
105c
1000uf
6.3v
There are 15 of them on the board and they are all bloated, can someone point me in the right direction?
Thanks -
Re: Yusmart 229IP-P 22" LCD Monitor Dead
Ok, so I've finally managed to find some time and traced the power button back to the IC on the Logic board.
It appears to be at pin 50 and doesn't go through any capacitors. I have attached some images showing this.
Can anyone give me my next move?...Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
Hi Billy,
I've not found a fix yet, i'm just working on making a diagram of the logic PCB to make things easier to trace.
I should have something done in the next couple of days so I can post something up.
Have you managed to find a datasheet for either the logic PCB or the IC from the logic board?Leave a comment:
-
Re: Yusmart 229IP-P 22" LCD Monitor Dead
I have also asked Quotidian at the post [url]https://www.badcaps.net/forum/showthread.php?p=125888&posted=1#post125888[/url] if he could measure the voltage he is getting at his power button.
Hopefully this will confirm if mine is ok or not.Re: Yusmart 229IP-P 22" LCD Monitor ...Hopefully thisLeave a comment:
-
Re: Very poorly Yusmart 2291p-p
Hi,
I have the exact same monitor and have been having problems with it, mine is totally dead though, see post at [url]https://www.badcaps.net/forum/showthread.php?t=11024[/url]
I was wondering if you could do me a favour and measure the voltage you are getting at the power button?
I want to rule it out as an issue on mine and have been unable to find a datasheet to give me any more info.
Also, where did you manage to find a replacement logic board?Re: Very poorly Yusmart 2291p-p
Leave a comment:
No activity results to display
Leave a comment: