Re: Halnziye HY610 Gold thermal compound
Load of rubbish then? Stick to mx4?
Ndagger
Member
Last Activity: 04-05-2018, 12:35 PM
Joined: 01-05-2018
Location: BRISTOL
-
Re: Halnziye HY610 Gold thermal compound
ConsiderablyLeave a comment:
-
Halnziye HY610 Gold thermal compound
Hi guys.
Has anyone tried Halnziye HY610 Gold thermal compound?
Gets pretty good reviews and is way cheaper than arctic silver.
Any input? -
Re: Acer 5552 thermal pad size?
If I'm ordering a couple of shims would it be wise to stick one on the southbridge too rather than re use the old pad?Leave a comment:
-
Samsung p5210 nand replacement
Hi guys.
I have a samsung tab 3 10inch model number p5210.
Something went horribly wrong when flashing and now it is dead dead, since I have no equipment to do jtag reprogramming I was thinking of swapping out the emmc with a pre programmed one that I can actually boot into recovery or download mode with but have scoured the net and can't find a replacement emmc for this model.
The p5210 is the 10inch 16gb tab 3.
I can find replacement chips for the t211 tab 3 7inch or the 5100 tab 2.
I don't suppose by any chance either of these could fit my needs? -
Re: Acer 5552 thermal pad size?
Thanks for the reply.
Please see the picture I've attached.
The chip nearest the dimm slots had the thermal pad on it, the cpu and the chip (gpu?) At the top.of the pic had thermal paste.
So you advise use paste on the 2 that were factory pasted and use a shim on the one nearest the dimm slots?...Leave a comment:
-
Acer 5552 thermal pad size?
Hi guys.
After repairing an acer 5552 with Intel turion cpu I need some advice regarding thermal pads.
The heatsink unit contacts the cpu gpu and chipset, the cpu and gpu had paste on it which I can replace, the chipset however had a small square of what I assume is a thermal pad.
I've no idea what thickness this is as stock so am not sure what to replace it with, I'm guessing as it's a pad out of the factory rather than paste the gap is to big for paste but have no idea of the thickness of pad to order -
Re: Hp g6 r23 motherboard fault
piernov you've been really helpful, thanks very much!
I was kind of thinking the FCH might be the culprit, nearly all google results on the g6 with this error sends you to YouTube videos of reflowing the chip, even though this board might be done for I've enjoyed tracing out the power rails and cross referencing with the schematic.
If you wouldn't mind one more question, you originally told.me to check APU_RST and then mentioned that the apu reset signal is deasserted, can you expand on that, what does this mean / how did you come to this...Leave a comment:
-
Re: Hp g6 r23 motherboard fault
I rechecked pu13 pin 6 and I measured 1.1v this time so I guess I didn't have good contact before.
Of the components you listed
Pl15 1.1v
Pl24 1.25v
Pu12 pin 6 2.52v
Pl19 0.9v
Pl23 1.13v
Pq41 pin1 5.07v
Pq56 pin1 1.53v
Pq38 pin4 3.3v
Pq4 pin4 3.36v
Pq13 pin1 3.36v
And
Pu8, pu5, pl22, pq1, pq22 were all bare solder pads with no components fitted, picture attached.
I also have attached the model of the motherboard incase the schematic is for a different...Leave a comment:
-
Re: Hp g6 r23 motherboard fault
Ok.
I've attached the schematic I'm working from and have measured a few points on the board.
U46 pin8 3.2v
Pq47 pin1 5.08v
Pr279 19.4v one side 17.37v other side
U30 pin1 1.5v
Pu13 pin3 3.36v pin6 0.7v
U23 pin2 5.02v
Pr281 3.3v
The fan spins and the cpu gets warm
Anyone see anything amiss here?...Leave a comment:
-
Re: Hp g6 r23 motherboard fault
Hi piernov thanks for the reply.
I'll check the power rails this evening and report back.
This is my first foray into motherboard repair, most of the repairs I do at work are on heating equipment so I don't have the equipment necessary for bios flashing. Since I'm looking at expanding my skills and doing more work with motherboards I'm open to getting myself a programmer. Would the ezp2010 be a good shout? Looking at the images I'm assuming I would desolder the bios ic, solder it onto the small board for the programmer that has the headers...Leave a comment:
-
Hp g6 r23 motherboard fault
Hi guys.
I've got an hp g6 1325 with the r23 motherboard.
It won't boot and the caps lock key is flashing once which all relevant faqs say is a cpu issue.
I doubt the cpu is dead as I've got another amd e2 3000 cpu which when installed doesn't cure the issue.
Any tips on where to look first?
I have the motherboard schematic and am going to take this on but thought I'd ask the pro's if you have any advice.
Also if anyone has a boardview for this board is very much appreciate a link if you could.
Regards
Neil -
Re: New Members - please post your introductions here
Hi guys.
Just registered here.
Seems like the best place to be for advice from experts!Leave a comment:
No activity results to display
Leave a comment: