hp 430 g3
charge indicator and power botton show when i isert charger, amp goes to 0040 0030 then settle at 0012
but pc not power when press botton
DAOX61MB6GO REV:G
SN 5CD5524S--- LAST DIGIT fadaed
i try bios up but no result
Backup attached...
akande
Badcaps Veteran
Last Activity: Today, 10:54 AM
Joined: 12-23-2017
Location: oyo state
-
HP 640 G2 CIRCUS-6050A2723701-MB-A02 DEAD
SN/5CG0094W3F
pls assist...Leave a comment:
-
HP PAVILION G6 NO DISPLAY
DAR33HMB6A1 REV A
SN/5CD32684V8
G6-2299EA
+vcc_gfx missing
backup attached please assiist.
tried many bios here no result...Leave a comment:
-
LA-E122PLeave a comment:
-
DELL LATITUDE E7280 NO DISPLAY
All voltages present
CAZ10 LAE22P
S/N: 3XHPMQ2...Leave a comment:
-
How to diable permanet absolute lock in BCU, Because Admin code keep appearing after follow the procedure
thanks...Leave a comment:
-
HP 430 G5 DAOX8BMB6G0 REV:G DEAD
All voltages checked power
i need bios rebuild
SN/ #5CD8420HCM
PRODID 1LR34AV...Leave a comment:
-
OK
But without ssd system work fine , no rebooting. once ssd in while loading before gettingdesktop pc will reboot and start booting process countously like that...Leave a comment:
-
after progrmming chip,
it keep showig this: Entering third party rom management.
i tried factory rest , change ssd still no result...Leave a comment:
-
THANKS BRO .
After programming , the pc keep rebooting when it about to enter desktop...Leave a comment:
-
HP 840 G4 ADMIN LOCK , I need code remove please
proid: X3V06AV
SN: 5CG8035056...Leave a comment:
-
I need clear for the file attached above in my post thanks...Leave a comment:
-
SN #8CG915KZFT
HP PROBOOK X360 440 G1
PROD ID 5YN95UT#ABA
RUMBLE KBL-RU 17869-1 448. OEQ07 001Leave a comment:
-
HP Probook 440 g1 x360 8th gen need clear me [ system work very slow]...Leave a comment:
-
Re: Hp envy m6 dead
yes i did bro and vin still 9v...Leave a comment:
-
Re: Hp envy m6 dead
Resistance to GND pin3=01.71, pin13=07.40 respectivly...Leave a comment:
-
Re: Hp envy m6 dead
Thans for concern, i pull pu301 earlier and pin12 still give 9v in the absence of pu301.
Ill measure the pin3 &13 resistance to GND and feed you back thanks...Leave a comment:
-
Re: Hp envy m6 dead
Pq105 pin4=9v . I think i need 10v-30v for the the N channel mosfet to switch normal?...Leave a comment:
-
Re: Hp envy m6 dead
Pu4 not working, all pins as 0v, kbc pin110 =0v
I think kbc need 3v Alw to function?...Leave a comment:
-
Re: Hp envy m6 dead
Pr112=9v, pq105 pin4=9v pin1,2,3=9v pin5678=19v pq301 pin=9v pq302 pin5=9v
TPS52225c changed earlier 2times...Leave a comment:
No activity results to display
Leave a comment: