Re: Help with Sprague cap replacement
Hi,
Any recommended replacement suggestions for this:
Sprague 501D106M063LL
10uf 63V aluminium axial electrolytic - is there anything particularly special about it being axial, could I just flat mount a standard equivalent radial?
Actually quite interested where this brand considered to be any good?
I found some for sale and they seem to be selling for a ludicrous sum of money!
Thanks,
FS...
firespace
Member
Last Activity: 02-06-2021, 06:37 AM
Joined: 08-28-2010
Location:
-
Last edited by firespace; 02-06-2021, 04:36 AM. -
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
oops your right, no charge, my bad too many tabs open with components, *laughs* thanks, I will order your choice, good to know I hadn’t picked something unworkable though, thanks again 
FSLeave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Could I use my choice without problems?
I can’t find the ESR rating for it or the original, but the one you list is a USA import and I get charged a handling fee of £15 from Farnell....Last edited by firespace; 03-02-2012, 08:15 PM.Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Very informative thanks so much, I hope you don’t mind but I PM’ed a little informal health info since you have been so kind sharing your knowledge, and I cure colds and coughs quite often
I hope it’s of use.
Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
5. (C57 board location). Samwha SD series, Model R7A, 400V 10uF 105°C (M) - Width 10mm Hight 21mm
[url]https://cdn.badcaps-static.com/pdfs/fa97f391d418478c65c19c5cffd5baf9.pdf[/url]
I have noticed the ripple rating for the original is 115 @ 120hz-
Hence my replacement choice of-
[url]http://uk.farnell.com/panasonic/eca2gm100/capacitor-radial-400v-10uf/dp/1907181[/url]
your choice-
[url]http://uk.farnell.com/panasonic/eeuee2g100/capacitor-10uf-400v-10x20mm/dp/1673487[/url]...Last edited by firespace; 02-29-2012, 10:09 PM.Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
You good sir are frakkin’ awesome today!
Thanks and I shall put a "good health unto thee and thine kind fellow" wish in the cosmic post to you immediately, the moment i’m done peeling those stamps of the last one I got sent..
- but seriously thank you and get well soon!
Yippy now to huff on some solder fumes while waiting for Farnell to send my goodies..
Corrections for others reading this looking to do the...Last edited by firespace; 02-29-2012, 02:18 PM.Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Cool beans, I shall add those replacements to the basket : ) now I just gotta get the others checked by someone, and look up a replacement for
6. (C57 board location). Samwha SG series, Model R8E, 50V 10uF 85°C (M) - Width 5mm Hight 10mm (might be 11mm hard to tell)
And then I shall be good to go.
Thanks Th3_uN1Qu3Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
I have been unable to find a data sheet for the Jamicon WG series that lists the 63V 120uF 105°C can anyplace on this here intereweb thingy, so I have no way of knowing what the ripple current rating was, but I'm gonna guess it was roughly the same as the Rubycon LZ series of the same stats
Rubycon LZ
120 8x7 380
120 6.3x11 405
I would say it is closer in can size to the 6.3x11mm can so I'm gonna go with 405 for the ripple.
I would really appreciate it...Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Ok so today I found these Panasonic as a replacement for the number 5 caps, anyone know of Rubycon Caps of the same specs, I couldn’t find any on Farnell but that doesn’t mean they aren’t there...
5. (C57 board location). Samwha SD series, Model R7A, 400V 10uF 105°C (M) - Width 10mm Hight 21mm (ripple 115 @120khz)
[url]http://uk.farnell.com/panasonic/eca2gm100/capacitor-radial-400v-10uf/dp/1907181[/url]Re: Allen & Heath XONE92 DJ mixer PS... <br /> Ok soLeave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Thank you Th3_uN1Qu3 very useful info.
I guess all I need now is links to the Farnell site for as many of the replacements as possible, and if some kind person could list what other caps I need I will source the rest myself.
Sorry if I am being demanding, I’m just learning at this and the guidance and assistance is very much appreciated. So glad I found this awesome forum, you guys are so friendly to share your expertise. - Thanks all : )Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Hi,
Just wondering would a lower ESR rating than the original component put more stress on components down stream? Should the ESR be as close to the original, or should I seek to make impedance as low as possible in all the replacement Caps?
Thanks,
FS.Leave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Hi PeteS,
Thanks for the clarification and added info, living in CA I doubt you would have any UK links, though even any USA based linkage for suppliers able to post to UK would be really helpful, I had a sniff about with google but had very limited results for the ZLG series or any of the others you mentioned.
FireSpaceLeave a comment:
-
Re: Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Hello Scenic,
Thanks so much for your helpful advice, which I'm gonna gratefully accept
So I will replace all the Samwha crapcaps.. yay! 
Here is all the stats for the remaining caps I could find, I believe the transformer winding is still fine, just looks a bit erm.. melted hehe.
4. (C61, C62, C58 board locations). Jamicon 324C4(M), 63V 120uF 105°C (M) - Width 8mm Hight 16mm
5. (C57 board location). Samwha SD series, Model R7A, 400V 10uF...Last edited by firespace; 02-19-2012, 03:16 PM.Leave a comment:
-
Allen & Heath XONE92 DJ mixer PSU board - (003-233JIT)
Hello all,
I am intending on fixing my A&H PSU board myself, since I cannot afford the £100+ for a new board, I can visibly see that some of the caps are bulging on the board and one has leaked (see pictures).
[U]The caps are as follows[/U]
1 (C57 board location). Samwha HC series, Model R3D, 400WV 68uF 85°C (M) - Width 22mm Hight 20mm
[B]Intended replacement[/B] - [URL="http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250840094893#ht_937wt_979"]Electrolytic Capacitor Samwha HK series, Model C92, 400WV 68uf 105°C...Last edited by firespace; 02-17-2012, 02:02 AM. -
Re: Repairing Alesis M1 Active mk2 Monitor Speakers
Bump -
If someone could make a replacement list from a good UK supplier for me I would be extremely appreciative, I would simply do it myself, however I am a novice at electronics although I have good soldering skills and can do the repair, choosing the correct components and tools to do the job well is beyond my limited knowledge.
I throw my predicament at the forums mercy.
Would anyone provide a supplier, item list, component order number, and price for the components required?
...Leave a comment:
-
Re: Repairing Alesis M1 Active mk2 Monitor Speakers
Ok so a whole lot of squinting with a flash light later here are all the caps (with details) for both boards on the active electronics of 1 monitor.
On the power supply board-
2x JunFu - Width 22mm Hight 35mm Dark Blue
390 uF
200V
HK105˚C
0304
2x Su'scon - Width 13mm Hight 20mm Brown
390 uF
50V
SD105˚C
0319 (V)
5x JunFu - Width 8mm Hight 19mm Green
220 uF
35 V
WG105˚C
0304...Last edited by firespace; 09-11-2010, 08:19 PM.Leave a comment:
-
Re: Repairing Alesis M1 Active mk2 Monitor Speakers
Ok so it's looking allot like I should recap the whole board on both monitors, at which point it might also be worth recapping the crossover board as well since that uses Jun Fu caps too, and doing so can only improve the reliability and sound quality.
Although if some kind person were prepared to give me the exact order numbers from a good UK supplier for all the correct replacement capacitors I could probably undertake such a project myself, (if someone would offer to do this for me, I would happily catalogue all...Leave a comment:
-
Repairing Alesis M1 Active mk2 Monitor Speakers
Hi,
(This is my first ever post on badcaps.net, (looks like a great place by the way) so please be gentle with me as i have very little real world experience practical or otherwise mending electronics, I know very little about capacitor ratings or the contextual meaning of these ratings within circuits).
I have a pair of Alesis M1 Active mk2 Monitor Speakers, they are wonderful, however recently one of them has developed a fault. When the monitor is switched on the blue LED power indicator simply flashes and there is no sound from the drivers when audio is sent to... -
Re: New Members - please post your introductions here
Hello BadCaps,
My name is Jo, I'm from the UK England.
I just found your wonderful forum and I am looking forward to learning lots of new information about BadCaps and what to do about them.
Thanks,
Jo.Leave a comment:
No activity results to display
Leave a comment: