Re: Sanyo FW65D25T with blue pixel picture?
Yea was the same board number just came from a different brand tv.
I probably should have mentioned that before....
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Sanyo FW65D25T with blue pixel picture?
Swapped eeprom chips and got it fixed!
Leave a comment:
-
Re: Sanyo FW65D25T with blue pixel picture?
It's the same, doesn't matter the input or menu. All is blue pixels....
Leave a comment:
-
Re: Sanyo FW65D25T with blue pixel picture?
It's through the whole screen, Would it matter if the mainboard came from a different model tv? Cause it did, would I need the eeprom chip from old main board?...
Leave a comment:
-
Sanyo FW65D25T with blue pixel picture?
I have a Sanyo FW65D25T that has a blue pixel screen. I have attached a piceture. Would this be a bad T-con? The TV takes a good 45 seconds to come on after pressing power on....
-
Re: Sanyo FW65D25T won't turn on, broken pwr button
I have attached a picture of the numbers that I seen on the back panel.
So the tv is stuck in the on position while the stand by light is still on?
Also when I plug the tv in I hear a small buzzing noise coming from the power supply board. This buzz goes away when I unplug the connector that feeds the main board and comes right back when I plug back in. I'm guessing the buzz noise is coming from a voltage reg or something to do with main board maybe being stuck in on mode? Or this is...
Leave a comment:
-
Re: Sanyo FW65D25T won't turn on, broken pwr button
The actual button circuit board is junk, the connector got ripped off the board and a few of the solder pads are gone too.
The stand by light never changes with any button presses when trying to program a universal remote. The universal remote says you are supposed to turn TV on first then press off to see if the code works. Maybe I should order the OEM remote for the TV and see if that changes anything?...
Leave a comment:
-
Re: Sanyo FW65D25T won't turn on, broken pwr button
Ok so in pic 1
24v 55v
24v 55v
24v 55v
24v 55v
24/12v 12v
GND
GND
GND
GND
GND
NC
BL_ON 55v
P_DIM 5.2v
Pic 2 I have 55v at the 4 red wires ZLED+
I can't power the TV on I can only plug into the wall and the stand by led comes on. So when I do that I get 55v at CED2...
Leave a comment:
-
Re: Sanyo FW65D25T won't turn on, broken pwr button
I don't have back-lights on or anything. Indicator light is still on. I can't get the light to go out no matter what I do with universal remote. (supposed to turn TV on to program remote. I have entered every code for TV and tried to turn TV on with no luck.
On the board with the video inputs Main board? The few fuses I seen tested good 5.2v on both ends or 12v on both ends. The Fuse on the FRC board or in pic 1 the triangle board. Has a fuse but no power either end. Also the 3 little red wires on...
Leave a comment:
-
Re: Sanyo FW65D25T won't turn on, broken pwr button
I will get you some pics of the back side.
I will also check for pwr on both sides of that fuse. I only have stand by right now. I can't get the TV to pwr on as the pwr button assembly is broken and I can't get the universal remote programmed to turn tv on. So I don't know how to cycle it to see if things are working.
Is there anything else I should check also?...
Leave a comment:
-
Sanyo FW65D25T won't turn on, broken pwr button
Ok,
Sorry for the multiple posts. I'm a noob and didn't read the sticky to this thread. And post the make and model in title.
I have a another post in this thread already. link it here and maybe someone can delete it? Start with this one instead?
[URL="https://www.badcaps.net/forum/showthread.php?t=65959"]https://www.badcaps.net/forum/showthread.php?t=65959[/URL]
My post from the other thread.
[INDENT]Hello all,
I have a sanyo fw65d25t that I picked up from someone who knows how a screw driver...
-
Re: Bypass power switch
Ok so in picture 1 is the IR&LED CON10 and the Key CN6. The pin voltages are as follows.
*PIC1
*CN10 goes to IR&LED board
L to R
3.2v, 3.2v
3.3v, 3.2v
GND
NC - 5.2v
5.2v, 5.2v
*CN6 Key
(Goes to power button asm that the other guy wrecked)
L to R
3.2v, 3.2v
3.3v, 3.2v
NC - 5.2v
5.2v, 5.2v
*Pic 2
*the first red connector (CN5 AMP PWR)
L to R
VR PWR, 12v
VR PWR, 12v
GND
GND
*Second...Last edited by kthorpe88; 11-22-2017, 02:56 PM.
Leave a comment:
-
Bypass power switch
Hello all,
I have a sanyo fw65d25t that I picked up from someone who knows how a screw driver works. He said the picture just would take longer and longer to come on and then one day it stopped. Well he tried to look at and managed to get the back cover off and wreck the power switch button.
So the indicator light comes on when its plugged in, I can't get it to turn on with a universal remote. He did say the back-light still worked just no picture. I'm wondering if their is a way to solder some jumper wires some place to turn it on with a switch?
...
No activity results to display
Show More
Leave a comment: