Re: Dell U3011 no display after a few minutes
...and a big thanks from me. Summer in Australia and with the extra heat my U3011 started going blank on me.
@Darran thanks for the pictures and instructions and @Eugene13 for the directions to the rectangular cap .
I found dry joints on the rectangular cap on the power board as others have reported. In re-flowing the joint I noticed that the solder was not sticking to the legs of the cap very well so like @essejlc I desoldered each leg and cleaned the little stub with some desoldering braid moistened with...
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Viewsonic VP2030b
Yes - thanks lucky. Thanks to the other posts on the forum I did find other bulging caps.
Last night I replaced:
3 x 180uf 35V on the inverter board
3 x 330uf 16V on the main board
1 x 1000uf 6.3V on the main board
1 x 220uf 25V on the power board
1 x 470uf 16V on the power board
1 x diode on the power board (shorted)
1 x 2.4ohm resistor on the power board (burnt)
All these caps were obviously bulging
The monitor is now working but I am hesitant...Last edited by Grubs; 09-15-2010, 04:14 PM.
Leave a comment:
-
Re: Viewsonic VP2030b
I've now accumulated all my caps for this repair but the resistors I ordered are of a different type. Can someone confirm if these are going to be suitable?
The markings I can read on the original are "2.4[ohm symbol]" and "1WJ" - thanks Rtech for confirming above.
I ordered 2.4ohm 1W metal film resistors - but they are a lot smaller and I'm wondering if I should have bought a different type or larger wattage (though appreciate they might just be a different design)?
I took the "1WJ"...Last edited by Grubs; 09-14-2010, 10:33 PM.
Leave a comment:
-
Re: Viewsonic VP2030b
Thanks for that. I removed the resistor and diode from the PCB for testing.
The diode appears to be a straight circuit - tester drops from 1.4V to zero in both directions. Marking say P6KE8.2A 5023 so [URL="http://au.farnell.com/vishay-general-semiconductor/p6ke8-2a-e3-23/tvs-diode-600w-8-2v-do-204ac/dp/1531799"]Does this Farnell part look right?[/URL] (Farnell had both P6KE8.2A and P6KE8.2A-E3/23 - the same?)
The picture below from another thread shows this resistor is marked 2.4 ohm but I'm measuring 50 Kohms
...Last edited by Grubs; 09-04-2010, 07:15 AM.
Leave a comment:
-
Viewsonic VP2030b
Viewsonic VP2030b monitor.
It briefly went blink-blink-blink and then when turned off for the night would not turn on in the morning.
On pulling the boards I found two bad caps in the PSU almost instantly and new caps have been ordered from farnell.
220uf 25V left of the heatsink: 1x EKZE250ELL221MHB5D 25v 220uf KZE
470uf 16v on the right: United Chemi Con EKZE-160ELL471MH15
The two 1000 uf caps laying down on the right of the heatsink appear fine.
I see some pretty severe scorching of the PCB around the grey resistor...Last edited by Grubs; 09-03-2010, 11:39 PM.
-
Re: vp2130b cap help
Hi guys,
Hope you dont mind me joining this thread.
I have 3x vp2030b. One just briefly went blink-blink-blink and then when turned off for the night would not turn on in the morning.
On pulling the boards I found the bad caps almost instantly and came looking here for help and found a great surprise with the info in this and the other vp2030b thread. THANKYOU. New caps have been ordered from farnell.
However.... I have some pretty severe scorching in the PSU.
The two caps that are oriented...Last edited by Grubs; 09-03-2010, 09:54 PM.
Leave a comment:
No activity results to display
Show More
Leave a comment: