[B]PP3v3_S5[/B] 3.271 v
[B]PP1v8_S5 1.790v
both present[/B]
[B]PP3v3_S5[/B] 3.271 v
[B]PP1v8_S5 1.790v
both present[/B]
[B]PP3v3_S5[/B] 3.271 v
[B]PP1v8_S5 1.790v
both present[/B]
[B]PP3v3_S5[/B] 3.271 v
[B]PP1v8_S5 1.790v
both present[/B]
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
[B]PPDCIN_G3H[/B] i am getting 19.88v keeps changing to 19.89v 19.91v, this happens on both ports
when i look on thermal camera both cd32s get like a hot dot spot inside them both of the the chips[B]PPDCIN_G3H[/B] i am getting 19.88v keeps changing to 19.89v 19.91v, this happens on both ports
when i look on thermal camera both cd32s get like a hot dot spot inside them both of the the chips3 Photos
Leave a comment:
-
r7602 = 001.1[B]Ω[/B]
[B]C7020 = 002.5 Ω, r7601 can not read at 800Ω[/B] no results at all on meter if i switch it to 800K[B]Ω will read 103.2kΩ[/B]r7602 = 001.1[B]Ω[/B]
[B]C7020 = 002.5 Ω, r7601 can not read at 800Ω[/B] no results at all on meter if i switch it to 800K[B]Ω will read 103.2kΩ[/B]r7602 = 001.1[B]Ω[/B]
[B]C7020 = 002.5 Ω, r7601 can not read at 800Ω[/B] no results at all on meter if i switch it to 800K[B]Ω will read 103.2kΩ[/B]r7602 = 001.1[B]Ω[/B]
[B]C7020 = 002.5 Ω, r7601 can not read at 800Ω[/B] no results at all on meter...
Leave a comment:
-
so measuring R7601 even if i swap the probes each side i get 100.6 k[B]Ω[/B], measuring R7602 again swapping either side i get i think much much lower which is 001.1[B]Ω[/B], if i turn my meter to 80[B]Ω and try to measure r7602 it will not give results, if i turn my meter to 800kΩ[/B] it would read R7602 and gives this result 100.6 k[B]Ω[/B]so measuring R7601 even if i swap the probes each side i get 100.6 k[B]Ω[/B], measuring R7602 again swapping either side i get i think much much lower which is 001.1[B]Ω[/B], if i turn my meter to 80[B]Ω and try to measure r7602 it will not give results,2 Photos
Leave a comment:
-
so f7000 fuse, with power connected i have 12.50v but it switches to 0.178v every second on both sides of the fuse, removed power, measuring the c7020 it gives very low reading, 002.3 Ohms ([B]Ω[/B]) other readings have been m[B]Ω
r7061 gives 100.9 kΩ, R7602 give low reading also 001.1 Ω[/B] both r7602 and c7020 which are near the chip give low readings
all those measurements are by touching with probes both sides of the capacitosso f7000 fuse, with power connected i have 12.50v but it switches to 0.178v every second on both sides of the fuse, removed power, measuring the c7020
Leave a comment:
-
hi, so it is not even 1 oms, when i start measuring it is 1.453 than if i keep holding it goes below 0.943 mo, same pin 2 and 3
5,6,7,8 2.579 mo
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-tempid":"temp_325033_1705788496516_512"}[/ATTACH] [ATTACH=JSON]{"data-align":"none","data-size":"medium","data-tempid":"temp_325032_1705788499845_831"}[/ATTACH] [ATTACH=JSON]{"data-align":"none","data-size":"med...1 Photo
Leave a comment:
-
hi there, first of all many thanks for your always help to the community in here
i am measuring this on diode mode and everytime i get different measurements
on source 1 2 3 some times i get 0.945 mo, some times i get 1.455 mo than if i start and measure again i get:
source 1; 1.650 and goind down mo, source 2: 1.389 mo and going down, source 3: 1.1745 mo and goind down
measuing the drain is a bit tricky as their is capacitors there on the way
drain 5, 6, 7, 8: 2.1 mo and going up
source 1 to gate 4 4.975 and going...
Leave a comment:
-
hello there, i would like to ask also for some help on this sort of issue, i also have a 820-01521-a which battery is not charging it show charging sign but it doesn't charge, the story of this is that someone has tried to replace the battery and i can see that this is not a genuine battery, i have got a genuine battery from another macbook and i am having same issue, i have done some measurements and i have the same as above user for those:
XA CC1 0.655
XA CC2 0.652
XB CC1 0.651
XB CC2 0.653
but with the battery not attached i get 12.46v f7000...
Leave a comment:
-
Hello, I am trying to read the ec I am using verytanov and 30 pin flex cable, do you have the settings for verytanov so I can read ec
-
Mp16q0vp serial
-
hi all
i have this laptop which has bios pasword is a 7th gen laptop lenovo yoga 710-14ikb i tried lenovo autopatcher from here but it didn't wok, this bios gives password blues screen
many thanks for help...
Leave a comment:
-
Re: Thinkpad L13 Gen 2 Password
Is ok I read the instructions of another user here and sorted 2 laptops, thank you...
Leave a comment:
-
Re: Thinkpad L13 Gen 2 Password
Hello there, thank you very much for your clear instructions this helped me
Read 2 laptops lenovo l13 gen 2 and lenovo yoga 13 gen 2, great instructions...
Leave a comment:
-
Re: Thinkpad L13 Gen 2 Password
hi is there any chance you can post the keyboard this as i am trying also to read with verytanov lenovo l13 10th gen, and is not working i am testing lar-1 and lar-2 but it doesn't read
LAR-1 KB_pins=36 LEFT DOWN 05MM FLASH=256 JENK=13 TCK=7 TMS=18 TDI=22 TDO=4 (evserv) CHIP=NPCE288GA0DX
LAR-2 KB_pins=36 LEFT RIGHT 05MM FLASH=384 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 (evserv) CHIP=NPCE68BPA1DX
i have tried both
chip on the board is nuvoton npce288ga0dx
i...
Leave a comment:
-
Re: Supervisor password on Lenovo T490 and T490s
Hi thank you for your advise I will try that in my future laptops as I have some x390 also and want to test on that, thank you very much I resolved this some
Guy edited for me and I dint have to use dmi, mine is resolved thank you guys...
Leave a comment:
-
Re: Supervisor password on Lenovo T490 and T490s
Unfortunately I am not quite advanced to edit files so I have to research how to get this done...
Leave a comment:
No activity results to display
Show More
Leave a comment: