Re: Mitsubishi LT-46249 no audio help
So I found a converter plugged it in and the sound works....nice
So now do I just go with the converter or try to troubleshoot the ic4a02??? Worth it or not??.
My bad on missing the dig out jack...sorry and thanks
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Mitsubishi LT-46249 no audio help
I’ll see if I can dig up a digital converter...i probably have one somewhere in the junk pile
Leave a comment:
-
Re: Mitsubishi LT-46249 no audio help
So yeah dig out does bypass everything...
Leave a comment:
-
Re: Mitsubishi LT-46249 no audio help
I was thinking optical but yes that is the back panel and it is rca dig out...I don’t have anything for that I don’t think, but I did plug it into the Bose input and got nothing...of course I don’t have a converter
2 shows surround sound...Last edited by Solderjerk; 11-09-2018, 06:29 PM.
Leave a comment:
-
Re: Mitsubishi LT-46249 no audio help
No headphone socket
I did...like I said if you look at that pdf I checked pretty much every red line which is the power flow...
Leave a comment:
-
Re: Mitsubishi LT-46249 no audio help
It doesn't have one...just analog out...
Leave a comment:
-
Mitsubishi LT-46249 no audio help
I have a Mitsubishi LT-46249 with no sound, video is fine, that I'm runnng out of ideas with
Video is fine, no sound out of speakers ( it has 16 built in speakers)
Besides all the obvious menu setting I plugged a Bose into the audio output of the tv...no sound. Put the tv in service mode that has a output test to static the speakers one by one...no sound (neither internal speakers and Bose)
Dug up the schematic, see attached, I checked all the hots (red lines)on this drawing and can't find a bad one...V is good everywhere. The audio circuit is part of the main board if...
-
Re: Bad panel or tcon TC-L55E50 LC550EUD
Just wanted to follow up in case it helps anyone...
I took lcd out and yes there is a crack and it follows those dead spots to a T. The crack was not visible from the front but very easy from the back.
And a note to everyone, these screens are very brittle, more so than normal. Use caution... I can barely bend it and it cracks
Leave a comment:
-
Re: Bad panel or tcon TC-L55E50 LC550EUD
I figured that but I can’t see anything in it...and I was super careful dissecting it. I’m so pissed
Leave a comment:
-
Bad panel or tcon TC-L55E50 LC550EUD
I'm pretty sure I know answer to this but is it a bad panel or tcon?
I'm so pissed off cuz i finished this tv finally and now I'm sure the panel is trashed
Short story in case it helps anyone out. Tv is a Panasonic TC-L55E50. Problem was it would blink the picture a couple times and the nothing, the power light would flash every 4 or 5 secs. Panasonics usually do this with a backlight problem. Took it apart, the panel was LG LC550EUD. Troubleshot any found 4 bad leds out of the 120. Replaced both strips and put back together. Tv fires up and works fine except for that big gray ...
-
Re: Schematics for Toshiba 40xv645u
Poked around alittle on the board...r840 is open, as mentioned, and it then feeds ic801 pin 5. Pin 5 & 7 are not shorted. 5 is not shorted to any other pins, 7 is shorted to 8. Ic801 is a mip2f2 ...pin 5 is a d and 7 & 8 are s so that should be ok. That's all I checked, had to leave for work
Leave a comment:
-
Re: Schematics for Toshiba 40xv645u
Yes that is the same board...
Don't have it front of me right now but I will check it and report back...thanks
Still would like to see a schematic tho to follow it, I'm still learning smps
Leave a comment:
-
Schematics for Toshiba 40xv645u
I'm playing with a toshiba 40xv645u power supply board that has no standby voltage. The board is a srv2194ww. I've got voltage up to the bulk cap but after that is where I keep getting lost on how it feeds the standby transformer. I was looking for a schematic but no luck finding one. I like figuring stuff out on my own so I'd like to try a schematic first before I actually ask for some help...anyone have a schematic or service manual?
No activity results to display
Show More
Leave a comment: