Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

well i effed up, i could not get solder out of one of the holes, i had a stroke of dumbness and thought i would ream the hole out with a small drill bit, unfortunately i drilled the solder pad right out and ruined the mount, i tried to fill the hole with solder hoping it would take but no, after getting everything else in the system would not post, it would power up but not post and no beeps, i tested the CPU mem and vid card in a separate board just to make sure i did not damage them and they still work fortunately....

Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

I just had the caps i ordered came in just now (i only ordered 10x of each due to the fact shipping was a flat 20$ for some reason) I would also like to thank momaka for explaining how the ESR will affect this boards power delivery, also i had only thought the 20% tolerance was down to capacitance not also ESR, and i think you right with replacing all the 820 uF KGZ, there is 11 on the board in total (including the ones i pulled) so i have enough and I'm also going to do all the 320 uF Evercon caps too, there looks to...

Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

ok i think i got this sorted out, for this [URL="http://www.paullinebarger.net/DS/Chemi-con/UCC%20%5bradial%20thru-hole%5d%20KZG%20series.pdf"]cap[/URL], I'm going to get 2 diffrent one because of high issues I
m going to have with one that exceed all the requirement, the shorter one is 2mOhms higher ESR then the old cap, here they are: [URL="http://ca.mouser.com/ProductDetail/Panasonic/EEU-FM0J102/?qs=sGAEpiMZZMtZ1n0r9vR22RbNZXJIUr%252b%2fdfagNNw20bg%3d"]EEU-FM0J102[/URL] and the
[URL="http://ca.mouser.com/ProductDetail/Panasonic/EEU-FM1A102B/?qs=sGAEpiMZZMtZ1n0r9vR22V2Y07khHJOUl5SulqehDq0%3d"]EEU-FM1A102B...

Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

Sry it has been a while, i had RL happened and the cap replacement project took a back seat for a while but im back now and I'm chomping at the bit again,

found a prefect replacement form the fatter of the 2 caps: [url]http://ca.mouser.com/ProductDetail/Panasonic/EEU-FM0J821L/?qs=MtOUKumLmnbB1Vkgi81JuQ%3d%3d[/url]

is a Panasonic FM series like someone recommended
The replacement ESR is 5 mOhms higher then the old cap but everything else is the same

I'm working on the Evercon...

Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

for the KZG, i think i found a suitable replacement:

[url]http://ca.mouser.com/ProductDetail/Panasonic/EEU-FR0J821/?qs=sGAEpiMZZMsh%252b1woXyUXjz6DqROYDxV8MxiJ%252bypO7zk%3d[/url]
[url]https://cdn.badcaps-static.com/pdfs/c64355fe61d9fff8d460e2e14313e448.pdf[/url]


the max Impedance is 0.020 ohms/100KHz higher, the ripple is 190Ma rms/100KHz lower, i dont know if these values are to far out of wack please let me know, also the ESR is 56 mOhms, the old caps just said low ESR...

Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

ok i have done some searching on mouser.ca and found some listing, but i have not idea what to get, also I don't know if there is a difference in 6.3V or 6.3VDC (this is all in the DC section in not searching the AC section), anyway this is the searches i did on mouser, if any one can help me narrow down what i need to replace my cap, thanks for you help.

[url]http://ca.mouser.com/Passive-Components/Capacitors/_/N-5g7r?P=1z0wrktZ1yx8e91[/url]

VDC:
[url]http://ca.mouser.com/Passive-Components/Capacitors/_/N-5g7r?P=1z0wrjoZ1yx4avt[/url]...

Re: Bad caps on a ASUS P5L-VM1394, need help im a noob at this

ok i pulled out all 6 caps this is what i have
2x Evercon E96C 105oC 6.3v 330uF
4X no name (cant find one) KZG 6(K) 6d 105oC 6.3v 820uF

I'm going to try to look for these parts on my own but i don't really know were to start for that so some help with getting the right caps would be appreciated

Hi this is my first real post here, anyway I bought a ASUS LGA 775 MOBD for a build i want to do and it looks like i have a few bad caps
I attached several pictures of said caps, the last pic is of caps between the ram slots and they are very slightly bulged, pls let me know if you thing i should get them two in the mean time im gong to focuses on the other 4 larger caps and as soon as i get them off i will get the info on what they are exactly.


Have started trying to desolderer with my 40watt iron and solder wick and im not getting very far, is my iron to dam small...

Re: New Members - please post your introductions here

Hello, I'm Kato

I need to replace some caps on a second hand MOBD I got on ebay, just came here to get some advice and help with doing that