Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Samsung un46es7100 issues
Hey guys i am working on this tv for a friend. So whats happening is the tv would just freeze. I can be in the middle of watching tv or a blu-ray and the tv would just shut off or just freeze. Also when i try to connect the tv to wifi it would just spin and not find any networks and sometimes freeze. I replaced the main hoping it would fix the freezing and it did a little bit. Not freezing as often. But wifi still freezing and still shutting off randomly. Indid hear awhile ago that samsung had a with the lead cable going from main to power that was causing the tv to shut off. I just dont know...
-
What should be the Voltages LED Strips?
So how can you figure out what voltage your LED strips are suppose to be producing? Meaning i am trying to figure out if the LED strips are bad or PB. Panel doesnt say what voltage it is suppose to be nor did i find anything online.
-
Re: Panasonic TC-65ax800U
Actually i found the service manual for that specific tv and the 6 blink error code is the A board (Main Board). Plus i tried pitting the screws on and the screws go right through the board. Screws are way to small. Thanks for your help.
Leave a comment:
-
Re: Panasonic TC-65ax800U
So i tested on the LED driver board the VBL test points. These plugs go from power supply to led deiver. The voltage was 24V when tv powered on and dropped slowly to 0. Then tested the VLED points that you requested and all the Negitive and positive points were 9V when tv powered on. Then when the tv shut down the voltage spiked to 11.5V and dropped to 0 really slow....
Leave a comment:
-
Re: Panasonic TC-65ax800U
Here are the pictures you requested....
Leave a comment:
-
Re: Panasonic TC-65ax800U
So i did a hard reset and he tv kicks on. You see panasonic pop up on the screen then the tv shuts down and goes back to 6 blink error code.
Leave a comment:
-
Panasonic TC-65ax800U
Hey guys i need a little help here. I purchased this 65" tv for super cheap but its not working. Im trying to find info on it and i cant find anything about it. The tv has a 6 blink error code on it. Now i tried finding 6 blink error code on this model and the only thing i find is about plasma tvs. This is a LED tv. Any advice? Here are some picture of the back....
-
Re: Whirlpool gold model GS6SHEXNS00 Fridge
Sorry guys i was out of town. I opened up the controller box that is next to the compressor, looked at the board and it looked like a small burn mark on the back. Here are some pictures. It looks like it is R34 but it also looks like the flat thin pin next to it. Dont know if i should just get a resistor and replace it. I dont even know which resistor i need. Plus when i installed the controller board back in the buzzing/clicking noise stopped....
Leave a comment:
-
Re: Whirlpool gold model GS6SHEXNS00 Fridge
Thank you, i clicked on the form and the samething he is experiencing i am as well. When you open the door you hear a clicking/buzzing noise. When you close it it stops. I will see if i see any bap caps or any other stuff that looks damaged. Thanks again guys for all the input.
Leave a comment:
-
Re: LG Dyrer Dley1201w
Its not the washer its the dryer. You set your dryer sounds like it wants to kick on but it shuts down. The drum wont move....
Leave a comment:
-
Whirlpool gold model GS6SHEXNS00 Fridge
So 2 days ago i went to get something in the fridge and the thermostat lights were off and the fridge lights were off as well. Fridge is still cooling but i am hearing a buzzing/clicking noise from the back of the fridge. Freezer lights and freezer still working. When i removed the back panel there is a box next to the compressor that it sounds like the sound is coming from. Im guessing a control board. Any ideas of what this could be?
-
LG Dyrer Dley1201w
I dont know if i am posting this in the right area. But i have a LG dryer model Dley1201w. When i turn on the dryer you hear the relays kick on but drum does not spin. No error codes. I also checked the belt around the drum and belt is fine. Anyone have any ideas or that can guide me in the right direction.
-
Samsung pn58c550 purple pixelation then fades
Hey guys so someone was throwing away this tv that didnt work. Brought it home and turned it on. The plasma looks like it tries to come on it would show pixelation very fantly and a bunch of purple dots just fades away. You have to disconnect the tv wait for the caps to drain turn it back on and it does the same and fades away. So i chcked with my meter the power supply for VA VS and VS i think if i could remember is 205V and im only getting 10V. VA is suppose to be 50-60 i think and i get 6v. So i am guessing the power supply is bad? I did plug in a bluray player and i am getting sound.
-
Changing option bytes
Question guys i just changed a main board in a sharp tv, do i have to change the option bytes on it? I know samsung you do. I was just wondering thanks.
No activity results to display
Show More
Leave a comment: