Hello,
Thanks a lot ! Awaiting new chips to not overwrite previous one. Keep you posted, thanks !...
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Veineda 1660 Super (pny xlr8 1660 super rebadged) - fan 100%
Hello all,
I have a veineda 1660super ( this is a rebadged pny 1660super xlr8, same pcb, same fans, same cooler)
Card is working fine, sensors reports fan speed at 32% but they are running at 100%. I thought it was only a fan issue, so decided to replace them but still same issues.... Wondering if I've not a problem with wiring.
Could someone that have one of both veineda or pny, post the cable wiring for the fan? (Color and order) or send the model of fans' on yours?
Also, if somebody have multimeter reading for each pin for the fan...
-
HP Folio 1040 G1 corrupted bios - new bios flash, unable to update DMI
Hello all,
I'm facing a strange issue, I do have my old bios where i can find some information about the laptop SN, build and so on for the DMI encoding.
I did flash a new bios on the laptop and i have tried all the tools found everywhere on this forum and other forums but i'm unable to update all DMI info in the BIOS. I still get an error saying "Warning: Machine is not in committed state".
Could somebody guide me on this or maybe help? I'm really hoping to find a way out of this bios thing...
See attached old bios (corrupted...
-
Re: Lenovo c740-14in
Thanks! Will look at it tomorrow!
Board view gives a lot more resistor/caps then what I have... Will see! Thanks again!
Leave a comment:
-
Re: Lenovo c740-14in
Looks to be that one yes, can you zoom out a bit on it? So that I have the area
Leave a comment:
-
Re: Lenovo c740-14in
Sure! Nm-c431
Looking for u3901 and around. It is located next to the wifi m.2 port...
Leave a comment:
-
Lenovo c740-14in
Hello all,
I was replacing the USB charge chip and noticed that I knocked off a cap 'ext to it. I'm not able to find the place it was sitting.
Does anybody have a picture of that area? It would be really appreciated!
Thanks a lot!
-
-
-
Re: Acer E1-731 Bios Unlock
Thanks, did check, i haven't those pins next to one of those ram slots.
I did found the service manual of the v3-771 (that looks similar to my model) and found the corresponding pins but unfortunately, it doesn't work either:
""Chapter 5
Steps for Clearing BIOS Password Check
If users set BIOS Passwords (Supervisor Password and/or User Password) for a security
reason, BIOS will ask the password during systems POST or when system enters the BIOS
Setup menu....
Leave a comment:
-
Re: Acer E1-731 Bios Unlock
Hey,
Thanks for the answer, I did forget to tell, i've seen this but i'm not getting any 10-digit, just that the system will halt and that's it.
Leave a comment:
-
Acer E1-731 Bios Unlock
Hello,
I'm trying to find a way to extract the bios password for an Acer E1-731. I've extracted the bios + EC but i have a lack of knowledge on how to find the bios password in the HEX editor.
This laptop is unused since 3 years and I did forget to remove the password at that time (i have another one where I removed the password when i decided to store them)
Find enclosed BIOS + EC.
Board number :69N099M13A01 - 12667677 - NBRYR11001346029B47200
Any hint or help will be much appreciated! :-)...
-
Re: request HP Probook 4530s bios dump
Works perfectly fine ! Thanks !
Leave a comment:
-
Re: request HP Probook 4530s bios dump
Hey !
Will give it a try, thanks !...
Leave a comment:
-
Re: request HP Probook 4530s bios dump
Hello,
Can I ask to remove the BIOS password? (see attached zip)
Did completely forget the password of the laptop...
Thanks!...
Leave a comment:
-
PSP Go - No backlight - fuse shorted (keeps shorting)
Hello all,
I have a PSP Go that is working perfectly on TV but nothing is displaying on internal display.
Screen is new, cable screen also.
I did jump the fuse (see pictures) with no luck.
When measuring on both side I get 1.29v on left side and 3.74v on right side. I do think that the 3.74v is fine but not the 1.29v. I've done some measuring around and found 2 caps that are shorting to ground (low impedance, but should be fine with readings 28.9ohms) but have no clue of where they are going.
I'm thinking that the 44c019...
No activity results to display
Show More
Leave a comment: