Re: Pantum P2502W Toner Reset Chip help
1
geekgirl1111
Member
Last Activity: 05-26-2019, 02:02 PM
Joined: 10-09-2016
Location: Philadelphia pa
-
Re: Pantum P2502W Toner Reset Chip help
.......Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
Since I needed a printer NOW I researched and found plenty of YouTube info on Brother HL-L2300D. Apparently you can only get them online now. They have a mechanical reset mechanism so it can get reset with a "reset wheel and spring". This kit is readily available on Amazon.
[url]https://youtu.be/ZlN4WGsAs3U[/url]
[url]https://www.amazon.com/TN-630-TN-660-DCP-L2540DW-DCP-L2520DW-MFC-L2720DW/dp/B00S7D3S24[/url]
I got the kit right away but it's still in the bag. I didn't have time yet to try it.Re:...Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
I saw those chips on alibaba. The contacts were not in the right position so I didnt get them.Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
Quote: from imajeff
"Some ppl are confused like geekgirl expected more contacts for address bits? That's not I2C protocol. "
What are you talking about? "more contacts for address bits" ??
You make no sense..
That's the second time that you dissed me. I will report you for rudeness.
I would comment about no wonder you are divorced but I'm not rude like you.
So knock it off.
We're all here to help each other in this project.Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
Did anyone just buy a chip? if so where?
There are different chip contact designs.
I'm not sure if they can be interchanged.Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
I know that the chips are under the blobs...
Lighten up!!
I unfortunately had to use the printer and the page count hit the max. It totally is dead and has no lights.
I haven't had time to work on it for a while.
Mine uses the same chip that is pictured in the first post. I saw chips for sale but the contacts were not the same.
I want to try covering the data contact and wire another eeprom up (on the arduino) but have a lead from the data pin in the printer to the external chip.
I suppose close circuit...Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
I hooked it up with an aduino.but only read 0's. Since it doesn't have the contacts for the address bits, how to proceed?
remove the blobs?
I refilled the toner, so now it still says that the toner is low.Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
I removed the Pantum software and only have the driver. Says low toner but still printing.
Says i still have about 200 pages to go.
Reload the toner outside with a mask. I read how bad that stuff is in your lungs. Its carbon and fine plastic granules that will melt into your lungs.
What clock speed did you get for the chip?
So 0x5B is the chip address in the printer?Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
I did a capture with wire shark while on wifi, but didn't have a chance to look at it.
Found an Arduino clone on sale for $10 and that they had a basic Ras Pi board for $5.
Got both and a few library books. Gonna try a hex dump. This weekend...
Has to be a way to just reset a simple adder or shift register.
And make the "allowed #of pages" increase to its max..
Now... how is the toner # generated??Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
I'm at the same place. Says 4% and expected pages 671 actual pages printed 350. I just put new toner from Amazon in. I saw someone said to leave it off for a few days. So it's off right now. I'm looking at the original pics of the chip and trying to figure it out from the visible parts of the circuit board. VCC is plainly labeled. 1v??
I read that it reads the density of the toner for the %. Hummm...
A review said that when it's down to 0 it will stop printing, so I'm not going to try printing until think Of something. Didn't...Leave a comment:
-
Re: Pantum P2502W Toner Reset Chip help
What chip re-setter can I use for the Pantum chip?
Most are for epson..
Thanks!!Leave a comment:
-
Re: New Members - please post your introductions here
Hi
I'm 62, MS EE, but little practical experience. I got my degree right before 911 and was out of work for some time. Finally got some tech work but NO design stuff. I have forgotten a lot but I understand it all. Doing retail rep field work now. I keep sending in the resumes......
I just wrote a lot more and it wiped out so this is version 2 with the basics.Leave a comment:
No activity results to display
Leave a comment: