Thanks for the info guys i'll open it again and see if i can find anything.
Thanks again for your time
johnis82
Member
Last Activity: 11-09-2021, 04:33 AM
Joined: 04-18-2016
Location: Florina
-
Re: Corsair TX-750 problem with finding component
Thanks for the info guys i'll open it again and see if i can find anything.
Thanks again for your time
-
Re: Corsair TX-750 problem with finding component
victorcas Do you have a schematic diagram for your PSU?Leave a comment:
-
Re: Corsair TX-750 problem with finding component
First of all thanks for the fast reply, i appreciate that! No i did not see that but i needed to find first the ic and then watch around the board for other component defects. Hmm you mean the little one next to the rectifier capacitor?(big one) do you know the value for this too?Leave a comment:
-
Corsair TX-750 problem with finding component
Hello guys i have opened a dead Corsair psu and i found a burned ic with 7 pins. Because i can't find any schematics for this PSU ,I said to ask a question here. Thanks in advanced!... -
Re: Useful Schematic component Code for Laptop
thanks for this!Leave a comment:
-
Re: Gigabyte GA-EP45-DS3
Hi kevin! thanks for the reply! What do you mean with "whatever the hell you, you put the same on the other ic" . replace the inductor with the same value of the other ethernet port? can you point this inductor on to foto i have post? if you have a schematic i will appreciate that...Leave a comment:
-
Re: Ecs g31t-m rev:1.0
pfrcom Thank you very much i did perform a successful bios reflash! But the problem still exists do you think is a north bridge fault or can you point something else that can cause this kind of problem?Leave a comment:
-
Re: Ecs g31t-m rev:1.0
wow didn't know i can reflash the bios! Thanks a lot
Can you give me more info to this it is a bit coplex to me!
Do i need to remove the bios IC from the board and reprogram it?
Can you explain the procedure cause i didn't understand from the site you post!Leave a comment:
-
Re: Gigabyte GA-EP45-DS3
Thanks Dan81, isn't that risky burning something else? if this component can be bridged then why the board has it?Leave a comment:
-
Gigabyte GA-EP45-DS3
Hi Does anyone have a service manual for this board or could help me identify the value of the component in the foto?... -
Re: Ecs g31t-m rev:1.0
The battery is 3,07volt but i changed it with a new one as you point, still nothing! Could that be a bad bios IC? And if so where can i get one?Leave a comment:
-
Re: Ecs g31t-m rev:1.0
Thanks guys for the responce i have done that! I have both ddr2-800 Good Ram pc2-6400 and ddr-667 Mushkin and kingston.
The board was working with one Kingstone kvr667d2n5 1gb and one mushkin 667 2gb for some years without problems!
There isn't any beep on system power on with or without ram on it (speaker connected on the board) and CMOS is cleared!
The think i don't understand is (like i said before) why the mobo powers up without pressing the power button or shorting the pins! Is like when you plug any PSU on it powers on without any other...Last edited by johnis82; 06-16-2016, 05:46 AM.Leave a comment:
-
Re: Ecs g31t-m rev:1.0
Thanks for the feedback but the motherboard doesn't post, no display or something! i can't get to bios. Only the cpu fan is spiningLast edited by johnis82; 06-15-2016, 08:46 AM.Leave a comment:
-
Ecs g31t-m rev:1.0
Hello guys iam new to this forum! It is nice to know people are not throwing away their staff and trying to repair it as i do!
My problem is with a mobo ECS G31T-M has got a q6600 cpu on it!
The problem is when i turn the psu switch on the mobo starts automatically working without pressing the power switch, no display!
I changed the psu and ram without any difference in operation!
I have tryed to repair it changing all 1000uf 6.3v caps but nothing, no cap seems to have a problem.
Iam working with the mobo out of the box!
Is there anything i can do... -
Re: ECS G31T-M - First Motherboard repair
Did you solve it mate? I have the same motherboard but a little bit more complicated problem! when i plug the power supply and turn on it's switch the motherbord auto turn on, no power switch pressed and it does not boot or something! It had an intel q6600 quad on it and ddr2-800 kingstone when it was working! The caps looks fine i don't have a Capacitance meter is there a solution to this or some dirrection to troubleshoot this?
Leave a comment:
No activity results to display
Leave a comment: