Re: Schematic MSI694D por2
The only big difference between the pro and the pro2 is that the pro2 uses the 686B chipset. The caps layouts has vary a little bit and the power connector is vertical. I think that MSI694D pro schematics could also help if you could not find the ones for the pro2.
I need these ones too!
Good luck.
DeadCap
New Member
Last Activity: 08-04-2006, 01:42 AM
Joined: 07-10-2006
Location:
-
Re: MSI 694D Pro AR Single Cap problem
If someone did not understood the question: I want to know if the tayeh points should be sourrounded by the dark green pcb circle (isolated). That's it, it's very clear.Leave a comment:
-
Re: MSI 694D Pro AR Single Cap problem
Here's a photo i took of the backwards. If someone can answer the question that's in the photo, please can someone can take a look at the back of your board to have the answer.
Is this point causing the issue?
Thanx.
Click on the image to get a better picture.
[URL=http://img470.*************/my.php?image=msi694dbacklx6.jpg][/URL]Last edited by DeadCap; 07-20-2006, 02:17 PM.Leave a comment:
-
Re: MSI 694D Pro AR Single Cap problem
Guess what. The wall plug has no ground, do you suggest to use a cable with ground?
I'll try to be more careful when working with PC components...photos are coming!Leave a comment:
-
Re: MSI 694D Pro AR Single Cap problem
I'm testing my mobo in a table to avoid any kind of contact, so the whole pc is on a table...is that what you mean with not grounded socket?...Leave a comment:
-
Re: MSI 694D Pro AR Single Cap problem
I think both cases are present in my board. I'll try to post a picture of the soldering point of the tayeh cap so you can evaluate if is doing contact with the circuit.
Ah! i almost forgot, sometimes i get an electric shock when i touch the board at certain points, it's a very small shock anyway so that makes me think there may be flux doing contact because all points are well soldered....Last edited by DeadCap; 07-13-2006, 02:36 PM.Leave a comment:
-
Re: MSI 694D Pro AR Single Cap problem
Right now the board does not work with 1 or 2 cpu's, it has the same error always. I tried clearing CMOS and all that troubleshooting steps, just left to try replacing the battery and tonight i'll try with a new 450w PSU.
I looked the board backwards for scratches but everything is ok i took a good look at soldering points, they are fine but i have doubts about a few ones, i think i added to much stain and posibly i made contact with a circuit, i removed and fixed these points but there's one imposible to remove all stain and...Leave a comment:
-
Re: MSI 694D Pro AR Single Cap problem
Hi, thanx for your answer. I repeat, both CPU's are fine, both of them work in another motherboard. I'm not able to enter the bios, i can only see post messages:
-GreenEnergy or something yellow Logo
-The award bios message at the top
-The bios rev. also at the top.
-The board specs at the bottom.
The first message a pc shows at post is about the cpu. I get the message: "Proccessor (Pentium III 1000 Mhz)" and then it freezes when it should print to screen
"Proccessor (Pentium...Last edited by DeadCap; 07-11-2006, 01:31 PM.Leave a comment:
-
MSI 694D Pro AR Single Cap problem
Hi there, new to the forum but i have read lots of post time ago. I'll bring you a very special Post after i solve this mobo issue.
Hope Bushytails the 694d expert can help me.
I'm another MSI 6321 owner, i have ver 1.0. When i first bought this board it had most of its caps vented so i replaced them as follow:
Stock Caps / Replacement Cap
6 Chhsi 6.3v 1000uf => 6 EA (they have a tri-star logo) 6.3v 1000uf.
6 Chhsi 6.3v 2700uf => 6 Nichicon 6.3v 2200uf
4 Teapo 10v 1500uf => 4 L X F 10v 2200uf
Then...
No activity results to display
Leave a comment: