Re: Find 2sc5707 equivalent
The replacement for C5707 are D1804 or C5706
stng
Member
Last Activity: 06-08-2014, 11:26 PM
Joined: 07-08-2006
Location: Malaysia
-
Re: Asus P4S533-E Dead Unit
It may not be the south bridge...The super IO chip could be the culprit sometimes..coz fail to communicate with the bios chip ...i fixed few boards before..Leave a comment:
-
Re: I need help with MS-6541
Yes, just change all the teapo and gluxon. as what kc8adu quoted..Leave a comment:
-
Re: MSI PM8M-V / MS7104 ver 1.0
Thanks everybody ..i have found the replacement part n the boards is up's for service again...Leave a comment:
-
Re: MSI PM8M-V / MS7104 ver 1.0
K' attach with the pic.....Leave a comment:
-
Re: MSI PM8M-V / MS7104 ver 1.0
Gosh..can anybody tell me how to attach a pic here ...Leave a comment:
-
MSI PM8M-V / MS7104 ver 1.0
Need help if anyone using this board coz mine the keyboard port not working
and found one of the chip fried and i couldn't see the part number on it .
the chip just above J3 conn or just left side of JPW1
appreciate if anyone can tell me the part no of the chip -
Re: GA8VM533-RZ V-core drop after POST
Can't continued further as suspacted one of the PWM chip that controlled the
Mosfet spoiled ..Leave a comment:
-
GA8VM533-RZ V-core drop after POST
Gor myself a Gigabyte GA8VM533 RZ,after troubleshoot.found out
one of the VRM mosfet shorted,the part no is FDD7030L ,i don't have
a actual replacement part so i get a nearer substitude 60N03H
and not sure is it becoz of not proper replacement part after i fired
up it POST but freeze at POST screen..then i check the V-CORE
and found out the V-CORE will drop from 1.75V to 0.08V ..
guys any idea what's coz the V-CORE drop ? anything to do
with bad cap ..have try change the cap but still same.. -
Re: MSI KT3 ultra MS6380E Ver 1.0 wired problem
But i think even with the D-Bracket i don't think it can let me know the problem
coz i still need to power up the board first before the indicator will indicate the error
right ..Leave a comment:
-
Re: MSI KT3 ultra MS6380E Ver 1.0 wired problem
Too bad i bought the board from somebody and it doesn't include the D-LED bracketLeave a comment:
-
Re: Asus TUSL2-C Ost recapping
I have a TUSL2-C mobo that don't post when power up ..only fan is spinning
but when i touch the clock controller chip it's hot ..is it this chip that cause
the mobo stop posting ?Leave a comment:
-
Re: ECS K7SOM+ On-board Processor burned
I measrued the mosfet to make sure there is no short mosfet before plugging
in the processor and power up ..err about the Vcore ..i do not known which
mosfet pin ..anyone can tell me...?Leave a comment:
-
Re: ECS K7SOM+ On-board Processor burned
Ok done with the ZIF socket ..when fired up,it just won't POST but the fan is spinning
so guys any idea ?Leave a comment:
-
Re: Abit AT7E freeze during OS boot
Not really know what series is it ..just remember it's green taepoLeave a comment:
-
Re: ECS K7SOM+ On-board Processor burned
Have the burned processor removed by slowly knocked the processor in pieces then
removed the pin one by one ..now is trying to fixed the zif socket ..Leave a comment:
-
Re: Abit AT7E freeze during OS boot
Yanz,
U can get it as a kit from here ...
[url]http://members.ozemail.com.au/~bobpar/esrmeter.htm[/url]Re: Abit AT7E freeze during OS boot<...eter.htm[/url]...Leave a comment:
-
Re: Abit AT7E freeze during OS boot
I have change most of taepo caps to OST and there's still left 3 of it
one near the ram slot and another 2 just beside the cmos batt connector...Leave a comment:
-
Re: Abit AT7E freeze during OS boot
I manage to fixed both of the boards ...unfortunately there is one board
first time can power on but after keeping for few days,try to power on
again it suddenly death ..power indicator on,fan spinning but no video
signal,try to removed each cap to confirm again but couldn't found
any bad caps...i wonder what cause this suddent death....Leave a comment:
-
Re: MSI KT3 ultra MS6380E Ver 1.0 wired problem
I notice most of the cap near VRM or the socket area are Rubycon ..
but when i measure the resistance between the P_ok and P_on
both ways give 0 ohm .when i compare other ok boards it's only one way
give 0 ohm and the other way some resistance..could it be cause by
badcaps ? or integrated circuit ?Leave a comment:
No activity results to display
Leave a comment: