Re: Asus A7N8X-E don't start after recapping
Hi,
Yesterday i recapped rest of KZG on my A7N8X-E. Five 3300uF and two 820uF near dimm. Now mobo working great and is stable as rock. I can run CPU on higher FSB then before without loosing stability.
Thanks all for help, and double thanks for PCBONEZ....
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Asus A7N8X-E don't start after recapping
Should I replace two KZG 820uF 6,3V near DIMM slots to?
Leave a comment:
-
Re: Asus A7N8X-E don't start after recapping
Hi,
Thanks for all suggestions.
Now motherboard is starting. Probably problem was with zapping bios. I took out battery and move the cap on pins for CLRT and keep it in this position for half minute, after that mobo started.
But I'm afraid of recapping rest of KZG. Should i recap all or use board with recapping 3 of 8 KZGs?
[ATTACH]24260[/ATTACH]...
Leave a comment:
-
Re: Asus A7N8X-E don't start after recapping
[QUOTE=bitok;157584]Hi
The mobo works before recapping. I checked all connection after recapping, there is no short. I tryed to running it only with CPU, RAM and Graphics card outside of case without positive result.
I try to comprehend what went wrong and in my opinion I destroy bios (if it is possible - the battery was on board), or ESR of assembled capacitors is too low KZG has 0,012 and MCZ 0,009 and delays the output signal, and the additional delay leads to another kind of instability and the board won't post boot....
Leave a comment:
-
Re: Asus A7N8X-E don't start after recapping
Hi
The mobo works before recapping. I checked all connection after recapping, there is no short. I tryed to running it only with CPU, RAM and Graphics card outside of case without positive result.
I try to comprehend what went wrong and in my opinion I destroy bios (if it is possible - the battery was on board), or ESR of assembled capacitors is too low KZG has 0,012 and MCZ 0,009 and delays the output signal, and the additional delay leads to another kind of instability and the board won't post boot.
Have You experience...
Leave a comment:
-
Re: Asus A7N8X-E don't start after recapping
Hello,
Attached is not real but for sure there are KZG.
My english isn't so good and I don't understand what mean "zapping BIOS" - something like destroy or damage? But for sure I didn't take out battery.
Leave a comment:
-
Re: Asus A7N8X-E don't start after recapping
I reseted bios. It changed nothing.
KZGs was repleace form one of VRM line. I marked them on picture:
[ATTACH]24220[/ATTACH]
Does replace rest 5 of KZGs form second branch of VRM change something?
I can't understand relation between replacing all KZGs and starting board, however before replacing this tree among one was blowed board was starting.
Could you explainRe: Asus A7N8X-E don't start after recapping
I reseted bios. It changed nothing.
KZGs...
Leave a comment:
-
Asus A7N8X-E don't start after recapping
Hello,
It is my first post on this forum. Till now i only fallow some topic.
Yesterday I decided to recap three 3300uf/6,3V Nippon KZG capacitors (form one branch of vrm) despite mobo works stable. I replaced blown caps for MCZ Rubbies. Recapping went without any problems, soldering pads looks relay fine but board didn't start. only collers of CPU and GPU are working).
Could You snuggest me what went bad? May be MCZ is to good and i have to use MBZ series of Rubbies (MCZ have too low ESR than original KZG). I dont wont to solder and desolder to many times before i'm sure of...Last edited by bitok; 03-29-2011, 12:19 AM.
No activity results to display
Show More
Leave a comment: