Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Sony has quit providing the updates for this model. Where else can I get the updates?
-
I tried the flashlight test but did not see any video. How can the main be paired to the TCON if you can't see the screen?
Leave a comment:
-
Sony XBR-65X850D
Customer brought in this dead Sony. I narrowed it down to a bad main. After replacing it, the front LED power light was flashing red and Green. When it stayed red, I turned it on and have no BL's but do have the music loop that will go up and down with remote but no BL's or osd.The power light is white but no picture. Why no BL's? And when I powered it off, there is no power light on the front.
-
Re: Hisense 65H6570G
I should of made my question a little more clear. How do you take the panel out? I see no trim holding the panel in.
Leave a comment:
-
Hisense 65H6570G
Does anyone know the procedure to replace the LEDs in this Hisense 65H6570G? I see no screws to take out to get to the bezel ect.
-
Onkyo tx-2500
The tuning knob on this receiver does turn the dial string but it is loose (like a nut came loose that holds it to the chassis). Does the knob pull off away from the stereo?
-
Lenovo On/Off Switch
Does anyone know where I can purchase the On/Off power switch for a Lenovo Desktop computer? The Machine Type is :3269 And the Model is A6U. It looks like the power button on some Delco car radios. Thanks!
-
Re: LG 65UH5500-UA Just Logo
Well before I could do any further tests, the set started working and has been for 3 days. Picture is bright all over the screen so will run and see.
Leave a comment:
-
LG 65UH5500-UA Just Logo
This 65"LG has the LG logo flash. Most posts say it is a classic LED failure. While hooking up my SJ tester I get 54v on each of the LED pairs (6 of them) and can see leds lighting up from the back of the set. My question is: with CN403 unplugged, does that 54v measurement sound right? Before I take the panel off I'd like to be sure of a bad led strip.
-
Panasonic TH-50PX80U
Does anyone know what 10 blinks code means for this Plasma? At the AC plug in to electricity I hear 2-3 clicks of the relay and there is 10blinks, a pause and 10 blinks again. No power up at all.
-
Re: Samsung LN32D403e2DXZA
I have replaced the main and the inverter boards with no change. I'm leaning towards a lamp problem. Asking the customer a few more questions, I find this tv is in a bathroom. Maybe the moisture caused a issue with the lamps. Thanks for the help!
Leave a comment:
-
Re: Samsung LN32D403e2DXZA
The voltage across CP803s is 166v SB and 393v when the set is on. Voltages at CON001 on the inverter board when on are: pin 9- 0 volts, pin 10-8.4volts, pin 11-12.7volts, pin 12-0volts.
Leave a comment:
-
Re: Samsung LN32D403e2DXZA
The answer to post #4 is the back lights come on for a half a second then go off. And with a flashlight , I can see the picture. I have replaced the Inverter and the main and still have no back lights.
Leave a comment:
-
Re: Samsung LN32D403e2DXZA
Backlights come on for half of a second then go out and stay out.
Leave a comment:
-
Samsung LN32D403e2DXZA
Customer brought this 32" in. Set will come on and you will have sound but the picture is only on for half a second. Sound is still there. Shut it off and same thing - sound always but picture for half a second. There is 12v on inverter board all the time. I replaced the main but same problem. What am I missing? When the picture is on, it looks a little dark. I see no lights behind the panel when it goes dark.
-
Vizio E470i-AO
Does anyone know the voltage that should be going to the LED plug? Is it 130V? I have 0 volts. The BL's will light using my SJ tester but there is 0 volts at the plug with or without the wires hooked to the plug. Could DM851 and 852 be bad?
-
Re: Sony KDL-50W800C
Yes it is a good picture on the side that is hooked up and a bright white screen on the side that is not hooked up. And when I switch the ribbons-my set will not power up.
Leave a comment:
-
Re: Sony KDL-50W800C
Unplugging the ribbon cable that goes to the left side of the panel brings up a picture on the right side of the set. I'll check to see if there are any shorted caps on the source board that is loading down the T-Con.
Leave a comment:
-
Re: Sony KDL-50W800C
Does not blow the fuse with the ribbons hooked up. But with the fuse replaced, I can't power up the set by pushing the power button. Take the fuse out and I can power up. I will try to find a T-Conn board and reply.
Leave a comment:
-
Re: Sony KDL-50W800C
I put in a new fuse and disconnected the 2 ribbons going to the signal board/panel. The fuse did not blow but the Sony light at the bottom of the set blinked Red ( It never did that before). Then I took the fuse out and tried it again and as before I had backlights and a normal lit Sony light at the bottom of the set. I'm leaning to something wrong on the T-Con board.
Leave a comment:
No activity results to display
Show More
Leave a comment: