Re: vizo e320i-ao
i wonder if i unglued the tabs half of screen should work like if i un gled the left hand tabs what u think
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: vizo e320i-ao
well i just got in a new/used main for this set an its doing the same thing
so i guess its in the pannel board
i have to look in to it so more
i do not have an scope so all i can do is check for volts on lvds cable an some are there i have no idea what volts should be there so i guess thats where i am at with this set i have the will to learn an if anyone know a way i shall try it
thanks for all the help as for this place rocks
Leave a comment:
-
Re: vizo e320i-ao
i am lost at this point will try anything
but i think the pannel is bad
Leave a comment:
-
Re: vizo e320i-ao
i check the fues on the pannle borad if this is what your asking
i think you are asking this because the main has t-con built in it
the borad that goes to the pannel on bottom of tv is where i am checking now right
yes 12.09 on both sides when on an 0 when off
i check the vollt reg on the labe location ic5 i belive thats what it says
line1 =1117
pin1=.61
pin2=1.87
pin3=3.32
from reading about these volt reg it look right on
i am lost after that thanks
Leave a comment:
-
vizo e320i-ao
ok all here is my issues with this set backlights come on nothing comes on sceen like no menu no vizo logo no bootscreen
i have test power board i i get 19v out very simple borad just one volt out
have been reading up on vizo eeprom an volt reg seam to big issues maker on these sets
so far i check the volts on reg at loction vp2 or up2 cant really tell
line 1 is 1117
pin 1 =2.0
pin 2=3.34
pin 3= 5.0
so i read online that you ad 1.25 to pin 1 so its close to 3.34
i just need an little help from...
-
vizo a320-a1
ok working on this tv set led replace the main board an still having same issues tv power on get backlight but no menu or pic on tv any help as what the case would be on the set ?? how do i test the tv pannle board i know its has 12 v going to it ....
-
Re: plamsa power supply
ok unplug the one cable going to y main it feed thes x main
volts are there
206 an 55
Leave a comment:
-
-
Re: ns-50p650 problem
when plug in the led light on main stay light for an sec then off
front light is on
then I hit power botton an
ok ok now it look like set is working just no pic
the bottons on side work like the should
hit channel button an the led light up like its moving channels same with vou up an down so I think the set is on just no pics
the vs volts come an go
206 then zero then 206 then 0
so what could it be ????
Leave a comment:
-
ns-50p650 problem
ns-50p650
when I remove this cable I get volts va vs
any help...
-
Re: plamsa power supply
ok all I need just an little help
could it be the main control board or the y sus ??
Leave a comment:
-
-
Re: plamsa power supply
the cable go from the y sus to the control borad
Leave a comment:
-
Re: plamsa power supply
the volts stay on with this cable remove...
Leave a comment:
-
Re: plamsa power supply
ns-50p650
no pic will not trun on
when plug in set get stand by then tries to start the click
vs va volts are there for 10-20 sec then gone
will get pics soon
test ps out of set an all volts are there
Leave a comment:
-
plamsa power supply
bn44-00330a
power supply
if I test this out of tv how long should the vs an va volt be on borad for
I get them for like 30 sec the off an then back on
any help
-
plamsa power supply
ok all I have an bn44-00330a
working on an plasma tv set
issues with set it no pic no sound trun on an relay cliks
checking ps out of set the volts are there
my qustions is how long should the vs va volts stay power up on ps
with the ps on to gnd an vs-on to 5.3volts should the ps stay on until power of or does the ps have an protect on it to shout down
the ps reads the right volts for 30-40 secs the shouts off
-
pwb dps-336ap
with pb out of set an nothing plug in exc power cord
is there volts to pson ??? all i read was that pson to ground to trun on
board i get standby volt an volts to pson 5.0 volts to bouth
-
Re: dell inspiron n5040 no power
i get volts on battery get when plug the chager in led comes up the one for chagaring
no power led
Leave a comment:
-
dell inspiron n5040 no power
hey all need help with this one
i have got no power to leds
i open it up it has an dv15 cp uma mb 10263-1 48.4ip01.011 motherboard
i get volts at f5401 24 volt fuse
i get NONE at f5501 it should be 6v
any help please
thanks brandon
No activity results to display
Show More
Leave a comment: