Re: Openflex Boardview: New boardview software (linux, windows and OSX)
Hi guys,
I found a key in one paste bin that starts with 0x25d8d248 and ends with 0xdacf7668. But in the obv.conf file they ask for a 44 sets of 32bits but my key only have 36 sets, is this the reason why i can't open the files. I'am using the lastest release with w7x64.
Thank you..
rtra
RuiAlmeida
Last Activity: 06-19-2019, 11:56 AM
Joined: 04-15-2015
Location: Oliveira de Azeméis
-
Re: Asus k54hr , turn on somethimes
Hi,
I have the same laptop, with the same problem.
The mine has a very low bright green on the led of the battery(second from the left) when it not starts.
My RT8206A does not heat. Sometimes i'am able to start the board if i HOLD the pwrbtn for like 30s, not always but sometimes works.
This laptop broke the conector and the costumer went somewhere else to repair, but came with this issue. So its possible to be some cap near the dc jack?
Have you found the problem...Leave a comment:
-
Re: Samsung ATIV Tablet dead
hi, how the repair end up going?
I have the same problem with the same tablet.
on mine, I have 3v on the power btn
on the battery connector i have
2.25(red bat wire)
2.25(red bat wire)
2.25(red bat wire)
3.0
3.0
3.0
0
GND
GND
Are these measures normal on the battery connector?
My battery outputs 7.035V i think this should be enough to boot the device or not?
What should i test next?
Thank you
...
Leave a comment:
-
Re: Toshiba C660 -1MK Completely dead, no lights at all.
Hi, do you have any news on this repair? have you replaced the RT8205A and it worked? Thank's...
Leave a comment:
-
Re: Toshiba Satellite A300 NO LED/NO POWER
Hi everyone,
I have here a toshiba a300 pcb: Inventec PT10G (schematic bellow) that have no led, no fan, no power on battery connector, no tension on power btn.
I measured the charger ICbq24271i get the following values:
pin1 CHGEN -> 18.9
pin2 ACDRV -> 5.67
pin3 ACN -> 0.19
pin4 ACP -> 0.19
pin5 ACDET -> 5.67
pin6 BYPASS -> 0
pin7 EAO -> 0
pin8 EAI -> 0
pin9 FBO -> 18.9
pin10 AGND -> 18.9
pin11...Leave a comment:
-
X551MA Boardview
For anyone who wants i have a boardview for this model. I have to buy it from somewhere else, and i am sharing with you... -
Re: Asus X551MA no boot
Thank you
Finally, the file was written
So the option to verify isn't necessary?...Leave a comment:
-
Re: Asus X551MA no boot
The version I'm using is 6.50. In Tools ->reflash firmware that option is disabled.
I can read the chip id with no problem.
I tested with your dump file and got the error too......Leave a comment:
-
Re: Asus X551MA no boot
Hi, thanks for your suggestion, but i have that adapter, it's a 200 mil 8pins.
First thing i did was read and save what it read. But if i try to write the file read previously i get the same error....Leave a comment:
-
Re: Asus X551MA no boot
Hi again,
Finally, I got a minipro to flash my bios chip.
I desolder the chip from the board and place it into the minipro. Made the read and save the file to have a backup.
After i download the file from asus site and loaded the file X551MAAS.515 into the minipro and hit "programming" with all the defaults, after a while i got an error like the photo attached.
I know i'am doing something wrong but i have no idea what. And this is my first time flashing a chip.
Can anyone give...Leave a comment:
-
Re: Hakko 900M soldering tips from Cantonmade, are they good?
Olá
I have a [URL="http://cdn.clickplus.pt/product_images/73648_Estacao-Ar-Quente-Daxis-TO0603_1.jpeg"] Daxis TO0603[/URL] like this one .
I think the tip you use will work awesome.
But I need also to replace the handle or at least my heater element(broken), and my doubt is what element to pick because apparently there are differences using a heater a1321 or a1322.
As i read somewhere i should use the appropriate one due the electrical diferences...
...Leave a comment:
-
Re: Hakko 900M soldering tips from Cantonmade, are they good?
Very interesting alternative :O
How good are these tips compared with genuine hakko? Have you tried it yourself?Leave a comment:
-
Re: Hakko 900M soldering tips from Cantonmade, are they good?
Hi, What you end up buying ? And the end result?
I have a daxis station too, but I have no idea what tip, heater, iron to buy.
Thank's
Leave a comment:
-
Asus X551MA no boot - BIOS
Hi,
I have a MB asus X551MA REV 2.0 tha only show the power led when i press the power button. No start the fan, no image, hdd no start spinning.
I have 19v on DC jack pins, but i have no clue what to check next.
Can anyone give me any hints?
(I'am a beginner on electronics, so i'am here to learn as much as i can)
Thank's -
Re: Asus motherboard K53SV schematic
I dont know if this helps, but i have a repair guide for this model......Leave a comment:
No activity results to display
Leave a comment: