Re: SONY KE-42TS2E-turn ON, then OFF immediately
Do you have a schematic diagram for this SMPS?
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: SCR - mountig substance
Ok....I found Penetrox A or A13....something like that...
Leave a comment:
-
SCR - mountig substance
Hello, I hope that I write in good section...
I need an ideea for a substance mounting some power SCR(thyristors) (2500 A) on a power collector bar, that are cooling with water...I am tinking some oil or white vaseline for good electrical and therm conduction....
I'm soryy for my bad English
-
Re: SONY KE-42TS2E-turn ON, then OFF immediately
Today I check Va and Vs voltages, and I found them with 2 Volts more then usually.
Va = 63,3 (noted on label panel) I found it 65,1V
Vs = 80.2 (on the label), I found it 82,5 V, measured with oscilloscope.
I putted them at correct voltage, from the label panel note and TV seems to run ok....
I don't know why, but I think that the problem may be some bad resistors .
When the TV was in run mode, I grow up Vs, at 82 V and TV stop immediately...that says that the protection are working at upervoltages ...And...
Leave a comment:
-
SONY KE-42TS2E-turn ON, then OFF immediately
Hello everybody and Merry Christmas!!! I have an problem with SONY- plasma tv, when I plugged in tv start an stop after 2 seconds, and red led flash for 2 times...if I repet the procedure make same thing...I have schematic, I check the smps and the voltage are ok.
I'm soory for my bad English and I need some ideeas...thank's
-
Re: Sharp LC32-SH340SE/V 17MB60-4
A firmware it is posible?please
Leave a comment:
-
Re: Sharp LC32-SH340SE/V 17MB60-4
Vgl=-4,89
vglin=-4,89
vcomr=6,82
vcomrfb=6.80
gvst=-4,84
vgin=-4,89
vgli=-4,89
vdde=26
vgip=26
zout=8.05
optin=3,23
vst=0
sde=0,63
hconv=0
pdl=1,61
Leave a comment:
-
Re: Sharp LC32-SH340SE/V 17MB60-4
There are presently that voltages on T-con.
Leave a comment:
-
Re: Sharp LC32-SH340SE/V 17MB60-4
I put a photo with left ribbon removed....
Leave a comment:
-
Re: Sharp LC32-SH340SE/V 17MB60-4
There are two ribbon cables and in bouth case ,when I snatch the ribbon, the half immage is white, and the ather still black. If I reverse, same thing.Last edited by catalin004; 12-04-2016, 03:19 AM.
Leave a comment:
-
Re: Sharp LC32-SH340SE/V 17MB60-4
Yed Idid, I have 12Vdc after fuse on T-con, and the voltage regulators are working on T-con.
Leave a comment:
-
Sharp LC32-SH340SE/V 17MB60-4
Hy everybody, I need a firmware for title LCD, I don't have any image to panel, backlight is present, but no image. Please help,
Best regards
-
Vestel 17MB55 - update software
Hello everyone....I need the software for an Tv "Princeton" with the chassis from the title. My Panel is VES275WNVXN01. Thak you for help
-
Re: Vestel 17MB62 Chassis
Hello all, I have a problem with the same chassis, 17MB62-1 of Vestel, the st-by LED is flashing at 1sec beat, the source is ok, I've tried to make an update of firmware and now the LED is dead....It is presently 5V, 3V3 an 12V but still not working.
Please an ideea.
The TV is LCD Tucson TL2201 B12
Leave a comment:
-
Re: LG 26LC42-zc image problem
No....it was the memory dump....it's ok now
Leave a comment:
-
Re: LG 37LF43 ZC - image problem
sorry LF45...I will try what you saidLast edited by catalin004; 02-08-2015, 09:27 AM.
Leave a comment:
-
LG 37LF43 ZC - image problem
Hy, I have a LCD tv that after 10 minttes the image apears like in image...I remove the T-con from Main, and I waiting 10 minutes with t-con deconnected, after I pluged in...It make same thing...I need help
[url]http://i59.tinypic.com/25owiee.jpg[/url]https://Hy, I have a LCD tv that aft...wiee.jpg[/url]
No activity results to display
Show More
Leave a comment: