Re: Samsung UN65C800XF No Power
So the part is replaced. Still nothing I would replace the board but I'm having a lot of problems finding it....
gamethriller
Senior Member
Last Activity: 01-22-2017, 05:17 PM
Joined: 10-21-2014
Location: Winter Haven, Florida
-
Re: Samsung UN65C800XF No Power
Thank You...Leave a comment:
-
Re: Samsung UN65C800XF No Power
OK do you know where to purchase? I can solder great dunno where to order from....Leave a comment:
-
Samsung UN65C800XF No Power
So I opened up this TV and pulled the powerboard to find this....Check photos would this cause no lights or power..... -
Re: INSIGNIA NS-L47Q09-10A: No Sound, No Picture
OK there is no flash no sign of black light or display with the flash light test.......Leave a comment:
-
Re: INSIGNIA NS-L47Q09-10A: No Sound, No Picture
TV is showing all the same symptoms. Everything else is showing good values also. I have checked the white fuses they ate good also. Not sure where to move next now. I thought I was gonna get by with a easy win but once I seen the value I kinda knew it was good. Just needed the confirmation. So any advice where I should go next.....should I open the display? See if there is any obvious problems there?...Leave a comment:
-
Re: INSIGNIA NS-L47Q09-10A: No Sound, No Picture
Budm same set sane problem. I set the meter to 200 ohms and the value is reading 1.1 ....is that a good reading I'm not sure. The black fuse says 15 on it....Leave a comment:
-
Re: Sceptre X405BV-FHD3 Powers on, logo appears, then shuts off
I replaced the eeprom on the new motherboard. I took the original eeprom from the bad board and now the tv works.Leave a comment:
-
Re: Sceptre X405BV-FHD3 Powers on, logo appears, then shuts off
Bad eprom maybe?
Or not bad for the wrong tv.....did you replace the mainboard?Last edited by gamethriller; 04-03-2015, 08:56 PM.Leave a comment:
-
Re: Sharp LC-60LE810UN
Thank you sir this worked for me........Leave a comment:
-
Re: Question about jumpering P.S.-on command
I have the same set and traced the one slow blink one fast blink to a bad led in the panel. I have fixed that problem but can not figure out how to clear out the error count to 0 to turn it on. Any ideals? It says in the manual the counts are cleared to 0 by the settings in the process A????Leave a comment:
-
Re: Horizontal greenish lines on Samsung UN55D6050
I take that back. I don't think the tabs would be bad here yet.Leave a comment:
-
Re: Horizontal greenish lines on Samsung UN55D6050
Have you checked the tab bonds on the display?Leave a comment:
-
Re: Sharp Aquos LC-42D62U Display Output Problem
I was able to reflow my mainboard for the 42" Sharp. I used a heat gun and liquid flux no clean.Leave a comment:
-
Re: M3D650SV White Vizio Logo No Power
Just a update. The mainboard got replaced and the tv comes on. But now there are black bars on the screen.Leave a comment:
-
Re: Samsung UN55D6050TF Power Light Blinking
I didn't remove them. I shaved down the LEDs with a razor knife. The one's that didn't work. You can see In the picture I just took solder to complete the led by bypassing the actual broken led. I only had a couple bad lights. I mainly did this for testing untill I find replacement leds. I did find a few post on ebay with full led strips for r and l for around 100. I never removed the led. If I was to get replacements I would solder the new one's on top of the old and call it a day.Leave a comment:
-
Re: Samsung UN55D6050TF Power Light Blinking
......Leave a comment:
-
Re: Samsung UN55D6050TF Power Light Blinking
More Pics...Leave a comment:
-
Re: Samsung UN55D6050TF Power Light Blinking
So I shaved down the LEDs and tined the tops with solder and we have bright lights lol....Leave a comment:
-
Re: Samsung UN55D6050TF Power Light Blinking
Finally opened her up. Pictures :-) I have about 5 bad lights maybe 6 on the right strip :-/...Leave a comment:
No activity results to display
Leave a comment: