Ok, Is it hard to solder? its a very small piece...
Antti
Senior Member
Last Activity: 09-27-2015, 12:28 AM
Joined: 09-07-2014
Location: ylivieska
-
Re: Ferm One electric screwdriver has no power
Ok, Is it hard to solder? its a very small piece...
-
Re: Ferm One electric screwdriver has no power
I just tested the motor, soldered the battery and motor off and connected them together, motor started rolling, so atleast motor is working
Leave a comment:
-
Re: Ferm One electric screwdriver has no power
it was still 3.64 volts when the charger was plugged in.
Greenlight was flashing like it does when its charging.... but it didnt charge...Leave a comment:
-
Re: Ferm One electric screwdriver has no power
Ok, it was only 3.64 volts, i charged it and waited about 5 mins, and it was still 3.64 volts... weird because last time I checked it, volts were higher and it started almost right away charge the battery.
...
Leave a comment:
-
Re: Ferm One electric screwdriver has no power
I asked the question 2 days ago, gotta go to work. This is only a hobby to me.
The slide switch is for Forward-Reverse function, and the micro switch is for the Trigger ON/OFF right? ---- Yes
I would hope that the OP has already tested the Voltage of the battery already before asking for help. ---- battery is fine
I dont have the time to measure components now, but i do it today..... or tomorrow...
Leave a comment:
-
Re: Ferm One electric screwdriver has no power
oh, well the admin can change this for the right place
I dont know how to test the power switch with a multimeter......
If you can see, the C3 component, is it a smf fuse? if the water did blow up only fuses..Leave a comment:
-
Re: Ferm One electric screwdriver has no power
heres the pics inside the screwdriver...Leave a comment:
-
Ferm One electric screwdriver has no power
Hello!
My friends screwdriver got water inside
and stopped working.
He loves it so much that it needs to be repaired.
If anyone has any idea where and what I could measure it would be really helpfull. Motor works fine.
here is some pictures... -
Re: Samsung LE 32A559P4C What is this part?
philips dps-138bp power supply,
is this part burn? the wires seems to be in a bad shape...
problem is that screen is all white, nothing. everything seems to be in good shape except that.....Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
yep, i tried, backlight did go on, but the picture didnt come :<
so new board is only option? id like to ask a question about another power supply, i take a pic so i dont have to make another thread...Last edited by Antti; 09-28-2014, 03:46 PM.Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
how i measure mosfets? If I put the multimeter in 200ohms mode, whats the right reading, if i touch the left and right pins it shows 1 of some mosfets and different readings on other......Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
I could try the backlight force, but need little bit more information, so 3v battery + -> inverted board bl_on and the other end? ground? how the cutting bl on wire, I simply cut it to peaces ? sorry my english.
Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
does this sound to you mainboard or powerboard problem?Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
i didnt undestand... tv powers on, when i plug the power cord, and red blink flashes 6 times, then theres no light at all (red led), power button wont get it blink again. instead tv´s blue light is steady all the time when the power cord is pluggedLeave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
bl=0.05
24v was normal every pinLeave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
as i measured rm801 it shoved me 00.05 ohms
multimeter was in ohm200 mode.........Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
how do i measure the rm801? should i solder it of first?Leave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
the main cab has weird clicking sound..... like it is trying to do somethingLeave a comment:
-
Re: Samsung LE 32A559P4C What is this part?
CNM802, 803 connectors gave me the 24v (five last pinholes)
i cant measure the main cab, its giving 360?
this multimeter reads only 300volts....Leave a comment:
No activity results to display
Leave a comment: