Re: Farfalla Induction Cooker FEC-20SD6 Error E6
Dear all,
I have put the main board front and back side by side to make it easier to check the connection. I also tried to start with the IC LM339N to see if what input that has triggered the error E6
Is this the right way?
Thanks...
maxchong2898
Member
Last Activity: 08-02-2018, 11:53 PM
Joined: 08-30-2014
Location: Singapore
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
dear goontron,
Thanks for reply.
Ok, the thermistor is ok
Anyway to identify bad solder or ic?
ThankLeave a comment:
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
dear goontron,
Thanks for reply.
Yes, it is true that most temperature sensors are in 10K Ohm.
see this site for various type of thermistors:
[url]http://www.amwei.com/views.asp?hw_id=61[/url]
How do I verify that it is the temperature sensor giving the problem, before I make a purchase?
ThanksRe: Farfalla Induction Cooker FEC-20...rature sensorsLeave a comment:
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
Dear goontron,
I got what you mean.
Attached are the pictures. The small one with 3 conductors are the temperature sensor for the coil.
There are two black wires. I measured the resistance across these wires both ways. The reading is 111.6 Kilo Ohm...Last edited by maxchong2898; 09-28-2014, 09:18 PM.Leave a comment:
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
Dear goontron,
Attached pls find the top panel pictures.
I still can't figure out what's wrong with the induction cooker
...
Leave a comment:
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
Dear budm,
Thanks for reply.
Initially, I suspected a capacitor was the problem, so I unsoldered the capacitor to do a testing on it. But it seems to be ok. Later I soldered it back and it looked like the electrical connection was damaged, so I soldered a wire across the connection
Leave a comment:
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
Dear RJARRRPCGP,
Thanks for reply.
That's what I suspect, but unable to find the thermal sensor on the PCB. Don't know which one is thermal sensorLeave a comment:
-
Re: Farfalla Induction Cooker FEC-20SD6 Error E6
Dear all,
Attached are pictures for the induction cooker. I am trying to locate temperature sensor on the PCB, but in vain. I know there is one at the center of the coil. Anyone knows which component on the PCB acts as temperature sensor?
Thanks in advance...Leave a comment:
-
Re: LG 42LD650 won't turn on, with standby red led on
I checked again, the red standby light is on when connected to main power supply. When the power button on the TV is pressed, the red standby light becomes dimmer for about 2 seconds, then restores back to the normal state.
It seems that the TV is trying to start, but fail to do so
Attached pictures on the back of TV, the power board and logic board with tcon
I can't find a separate tcon board
Thanks in advance...Leave a comment:
-
Re: LG 42LD650 won't turn on, with standby blue led on
Dear bil99,
I don't see any back light turning on.
I also think that the blue led light is still there even though the power on button is pressed.
I will take some more photos when back home, and try to post over weekend
ThanksLeave a comment:
-
Farfalla Induction Cooker FEC-20SD6 Error E6
Dear all,
I have an induction cooker FEC-20SD6, when turned on showing error E6 which is 'internal temperature is too high' according to the user manual. I am trying to fix the problem but in vain. Hope can get some advice on how to fix it
Thanks in advance -
LG 42LD650 won't turn on, with standby blue led on
Dear all,
I have got a LG 42LD650 TV that refuses to turn on when power button is pressed on the TV. I took out the power board (EAX61131701/11) that is with inverters on it (see pictures). I connected the power board to the main, connected one of the 3.5V pins to the Power_On pin, and tested the voltage outputs of pins 12V and 20V. The DMM shows readings close to the values.
What should I do next to troubleshoot the TV?
Thanks in advance!... -
Re: New Members - please post your introductions here
Hello Everyone, I am Chong
I come to this forum to learn some electronic stuff and also would like to know some expertsLeave a comment:
No activity results to display
Leave a comment: