Re: Dell E173FPf
No, I haven't yet. I got busy with some other stuff going on so i had to set it aside for a while. I am getting ready to get back at so. I kind of think it 1506-50 since I had such different reading then everyone else.
darkstar
Member
Last Activity: 07-06-2010, 12:43 PM
Joined: 02-18-2009
Location: Austin, Texas
-
Re: Dell E173FPf
Thanks again Eduardo and Bob for the helpLeave a comment:
-
Re: Dell E173FPf
Ok i can agree with that. What kind of details would they need? What numbers off the board do i need to give? I have a white sticker with numbers on it and a bar code and numbers printed down by the power plug and a set on the back. I also have the pictures i took in better quality i can email someone. The quality was sacrificed in order to post them on this thread.Leave a comment:
-
Re: Dell E173FPf
Hey
Yes i am not sure what to think about those read outs either. I am hoping i don't have to remove anything off the board just yet. I don't want to damage anything that is not damaged. So i will have to wait on that. Well write back if you find anything else that will help. I will keep on reading.
Thanks for the help
JustinLeave a comment:
-
Re: Dell E173FPf
Ok well after testing it multiple times this is what i came up with on my velleman DMM set to diode check or 2k on the ohm selector
(-) on P3
5 pin .000 ohms or 00.3 ohms if i set it to 200
4 pin 1.701 ohms
2 pin 1.705 ohms
1 pin 1 ohms
(+) on 3
5 pin .000 ohms or 00.3 ohms if set to 200
4 pin .201 ohms
2 pin .203 ohms
1 pin .293 ohms
I did not disconnect the pins from the board.
As far as the ap2761i if i put the (-) on g and (+) on s it starts at...Leave a comment:
-
Re: Dell E173FPf
Ok, Well thank you for the help I will keep reading. I don't know what would have caused the green LED just to shut off. I haven't done anything but check ohms on things that i have been reading about.
I think i have another suspicion. That would be the diode above the yellow transformer on picture to up there. I read a thread that said to check the SRF10-10 and that one seemed to work fine but the other one i can't get an ohm reading for it. The numbers on it or 27611 or 1l I'm not quite sure about the last 2. Then below that set is another set 430036....Leave a comment:
-
Re: Dell E173FPf
I am not sure yet if I want to lift those pins. I don't want to do something and not be able to put it back. Is it difficult to solder those pins back on? My experience is guitar cables, pick ups, input jacks, and wires. Nothing really that small, so I am still debating.
So I put everything back together to see if I could see any kind of flash or any kind of light on the screen and now The green LED is not coming on. So I think i am moving backward here.
I guess i was also thinking, could it be back lights in the monitor? Do those...Leave a comment:
-
Re: Dell E173FPf
Hello Bob,
I went back and read his post and from what I gather he said, is that I should not have continuity between pins 1 and 3 which I do not. If I have the power hooked up I get 12v off of the 1 and 3 pins but I do not get any volts off of the 3 and 5 pins. The 3 and 5 pins also read 0.3 off of the ohm meter. I'm still not sure if that is right or low. I think it might be kind of low if his was reading 0.9 I figure mine should be somewhere close.Leave a comment:
-
Re: Dell E173FPf
Here are the pictures for the board...Leave a comment:
-
Re: Dell E173FPf
Yes there is continuity. My ohm meter is reading 00.3 when i put it on the the 3rd and 5th pin. Nothing at all comes on the screen, it is just black. I get the green light when the monitor is not plugged into the computer and the amber LED when i have it plugged into my computer. I am trying to get the pictures of the board uploaded but i am having problems getting them small enough so i will post them as soon as i can. Thanks again Bob.Leave a comment:
-
Re: Dell E173FPf
Thank you for the help. Yes there is a connection between the pins. I have my meter set on ohms 200 and it is reading 00.3Leave a comment:
-
Dell E173FPf
I have the monitor listed above. Nothing will come on the screen but i have a green light when its not plugged in and a orange light when i have it plugged into a computer. I have read through past forums and checked the srf10-10 diode and it seems to be fine.
No activity results to display
Leave a comment: