Samsung ue49mu6120

[lotas]

You are doing everything correctly, only the contacts on the chip must be cleaned of flux, rosin, solder residues and the contacts on the block must also be clean...

[crystalsound]

I installed a working mainboard taken from a ue55mu6120k and it's perfectly working without modifying anything, even on the 25q80, nothing. But I'd like to fix the original one. I wrote the original dump I posted here and it used to turn on and off with no video, but now it doesn't boot at all, I don't know if the reason is the dump, which may be corrupted as you suggested, or a matter of register, although I followed your instructions. Isn't there any way to write a "default" firmware for this model? What if someone has a TV with a faulty flash - and therefore with no dump to fix?

[lotas]

There is no standard firmware, since it changes when updating the software, the software version 24Q40 must match the eMMC software version, if the standby mode does not appear (STB LED does not light), then the dump is not recorded correctly (status register) and the first time it is turned on, it is damaged again. ..
The fact that you posted your dump, was it original, native, or was it after experiments, recorded on it without saving its original?

[lotas]

What if someone has a TV with a faulty flash - and therefore with no dump to fix?

I can fix any original dump from this "MU" series or look for a donor (motherboard)...

[crystalsound]

There is no standard firmware, since it changes when updating the software, the software version 24Q40 must match the eMMC software version, if the standby mode does not appear (STB LED does not light), then the dump is not recorded correctly (status register) and the first time it is turned on, it is damaged again. ..
The fact that you posted your dump, was it original, native, or was it after experiments, recorded on it without saving its original?

it was definitely original. But the native problem of the tv was not "no standby at all", it was booting with backlight and no image, 4-5 seconds with audio then off and reboot again. I desoldered the 25q40, read it and posted here without doing anything else.

[jaypay15]

Dear lotas if you could can spare the time to fix the attached bin I would be very grateful.
Regards Jamie

[lotas]

Dear lotas if you could can spare the time to fix the attached bin I would be very grateful.
Regards Jamie

Try.

[jaypay15]

Try.

Thanks so much I will let you know how it goes.

[lotas]

Ok. Don't forget about the register status...

[jaypay15]

I flashed the bin and register value but the TV is still dead. I read the chip back and the bin was intact. Thanks for your time.

[lotas]

I flashed the bin and register value but the TV is still dead. I read the chip back and the bin was intact. Thanks for your time.

It's strange, but everything should have worked if everything was done correctly, except that it wouldn't have hurt...

[adiasterix81]

can someone check my bin? I dont have the stanby led. TV - Samsung ue49mu6120kxzt - IC1604

[lotas]

can someone check my bin?

Here, in my opinion, I didn't see anyone except me that I could check and correct. Try it.

[adiasterix81]

Here, in my opinion, I didn't see anyone except me that I could check and correct. Try it.

Hy. It worked. Thank you. God bless you

[lotas]

Hy. It worked. Thank you. God bless you

Ok! Thank you!

[sirjoe]

Hi, I have a Samsung ue49mu6470 with the stand by LED off problem. The power board works fine as does the panel. I would like to try with the w25q40cl firmware fix.
The model of my TV is
UE49MU6470UXZT
Main Board BN41-02568B / BN94-12399P
I attach the original dump (AsProgrammer)
Thanks

[lotas]

Hi, I have a Samsung ue49mu6470 with the stand by LED off problem. The power board works fine as does the panel. I would like to try with the w25q40cl firmware fix.
The model of my TV is
UE49MU6470UXZT
Main Board BN41-02568B / BN94-12399P
I attach the original dump (AsProgrammer)
Thanks

Try it. Change the program to NeoProgrammer V2.2.0.10, it works more correctly than Asprogrammer with status registers settings.

[pellas]

Hi, Samsung UE55mu6455 here. Can you have a look at my file please?

[lotas]

Hi, Samsung UE55mu6455 here. Can you have a look at my file please?

Hi, I looked, it was damaged, I fixed it, try it.

[pellas]

Works! Thanks a lot! I even managed it using the clothespin.