Samsung un49mu7000f dead no power

[steven91919191]

What's the problem? Is the standby LED on? Does the backlight come on when you disconnect the motherboard from the power supply?

Hi Iotas,

Are you still active here? Our TV backlight works with MB disconnected. I can upload from eeprom for fix maybe?

[lotas]

Hi Iotas,

Are you still active here? Our TV backlight works with MB disconnected. I can upload from eeprom for fix maybe?

Hi, I'm still here, post your original dump here, I'll check if that's the problem.

[steven91919191]

Hi, I'm still here, post your original dump here, I'll check if that's the problem.

I tried to read it but says device disconnected or defective so i cant read it! New MB need to order

[lotas]

I tried to read it but says device disconnected or defective so i cant read it! New MB need to order

How do you read dump, using a clothespin or through an adapter, which programmer, post a photo of how it is connected to your programmer...

[steven91919191]

How do you read dump, using a clothespin or through an adapter, which programmer, post a photo of how it is connected to your programmer...

Its on a CH341A (ive flashed loads of BIOS with it) - just this one doesnt want to read. Dont use the clip or anything, always desolder and solder to the programmer board

[steven91919191]

Its on a CH341A (ive flashed loads of BIOS with it) - just this one doesnt want to read. Dont use the clip or anything, always desolder and solder to the programmer board

The chip actually gets hot while reading too on the PC. I switched it to 3.3v and still cant be read

[Diah]

The chip actually gets hot while reading too on the PC. I switched it to 3.3v and still cant be read

be sure you installed the chip in correct way... pin 8 should be at 3.3V

[steven91919191]

Here it is

[Diah]

if it at time installed at MB didn't get hot,,, i will prefer install it back and use clip.. other wise it will be expensive repair

[lotas]

Turn the adapter 180 degrees.

[steven91919191]

if it at time installed at MB didn't get hot,,, i will prefer install it back and use clip.. other wise it will be expensive repair

I dont have clip for this. This is an old programmer. I do have new MB coming tomorrow would like to repair this and then return board

[steven91919191]

Turn the adapter 180 degrees.

Such as this??

[lotas]

Yes! If you haven't burned the chip yet!

[Diah]

lotas have right turn the the plate 18ß degree

[steven91919191]

Okay the pads on the adapter was slightly broken. Only missing about 1mm or less! I have jumped it and got the dump now Sorry!

[lotas]

Okay the pads on the adapter was slightly broken. Only missing about 1mm or less! I have jumped it and got the dump now Sorry!

Try it, don’t forget about the register status (0x88, 0x42) after writing the corrected dump.

[Diah]

fly out ... lotas will do it

[steven91919191]

Thank you. I will try in 15 minutes when I'm back home. Can you clarify what you mean by register?

I have colibri or neoprogrammer. Or I can download another if necessary of course

[lotas]

Thank you. I will try in 15 minutes when I'm back home. Can you clarify what you mean by register?

I have colibri or neoprogrammer. Or I can download another if necessary of course

Yes, neoprogrammer is exactly what you need for this.
In the program:
1. Click "Detect Chip" and select W25Q40CL and "Select IC".
2. Click "Unprotect".
3. Click "Clear IC" and "Yes".
4. Click "Open File" and select your corrected dump.
5. Press "Program IC" and "Yes".
6. Click "Verify IC".
7. Press the down arrow to the right of "Unprotect" and select "SREG Edit", put a check mark on SRP0, BP1, CMP, QE and press "Write" and "Yes"
7. Close the program. Ready.

[steven91919191]

Yes, neoprogrammer is exactly what you need for this.
In the program:
1. Click "Detect Chip" and select W25Q40CL and "Select IC".
2. Click "Unprotect".
3. Click "Clear IC" and "Yes".
4. Click "Open File" and select your corrected dump.
5. Press "Program IC" and "Yes".
6. Click "Verify IC".
7. Press the down arrow to the right of "Unprotect" and select "SREG Edit", put a check mark on SRP0, BP1, CMP, QE and press "Write" and "Yes"
7. Close the program. Ready.

Thank you for this. My status register #2 is set to 40 (I cant change it or select QE box). The write button is greyed out