Skyworth 40E58 no display

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • yobbgsm
    Senior Member
    • May 2017
    • 63
    • USA

    #1

    Skyworth 40E58 no display

    Hi Experts,

    I have a here, a 40" LED TV brand is skyworth, I thought it was a backlight issue since I can see a display using a torch. Voltage are good up to 37V output to LED. I opened it up and test all the backlight to find out nothing is busted. All are good. I rehot the TPS61196 Led dirver IC, assembled and test, seeing dispaly and I even the set the backlight but after closing the unit and boot up again, same issue occur, ni display again likeno backlight. Do you think the Led driver IC is the culprit? Voltage are good to the backlight. Any idea is very much appreciated.

    Pics attached of the board.
    Attached Files
  • budm
    Badcaps Legend
    • Feb 2010
    • 40746
    • USA

    #2
    Re: Skyworth 40E58 no display

    It looks like the boost converter is not working, I expect more than 37 Volt.
    Put the meter probes on the two legs of either one of those tow lytics cap (CP2, CP3: 100uf 100VDC) laying on its side then turn the TV on to see how high it goes up too and then wait 5 seconds to see how low it goes down too; then remove the LED connector and do the same test and report the results.
    Never stop learning
    Basic LCD TV and Monitor troubleshooting guides.
    http://www.badcaps.net/forum/showthr...956#post305956

    Voltage Regulator (LDO) testing:
    http://www.badcaps.net/forum/showthr...999#post300999

    Inverter testing using old CFL:
    http://www.badcaps.net/forum/showthr...er+testing+cfl

    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
    http://s807.photobucket.com/user/budm/library/

    TV Factory reset codes listing:
    http://www.badcaps.net/forum/showthread.php?t=24809

    Comment

    • yobbgsm
      Senior Member
      • May 2017
      • 63
      • USA

      #3
      Re: Skyworth 40E58 no display

      Hi budm,

      Your always helpful, appreciate it. So I followed your instructions and got these results.
      Caps- 55V high then went down to 30V.

      Same result on the LED connector. Do you think there is an issue on the voltage?

      Thank you so much!

      Comment

      • yobbgsm
        Senior Member
        • May 2017
        • 63
        • USA

        #4
        Re: Skyworth 40E58 no display

        Do you guys have a schematic diagram for this model? Thanks.

        Comment

        • budm
          Badcaps Legend
          • Feb 2010
          • 40746
          • USA

          #5
          Re: Skyworth 40E58 no display

          OK, at least the Voltage Boost converter did kick on for seconds,
          Next thing you need to do is to test the Voltage on all 6 wires (6 wires are what I can see) at the LED connector (connector in place).
          Start by leaving the TV off and leave Black meter probe on the chassis, then put red probe on one of the 6 wire and then turn on the TV while looking at the meter to see how high the Voltage go up to, record that reading and then turn off the TV.
          Repeat the same procedure on the other 5 wires and report your finding.
          https://www.badcaps.net/forum/attach...4&d=1508126628
          BTW, I can see that the LED connector has the pin labels for each pin but I can hardly see it.
          Attached Files
          Last edited by budm; 10-17-2017, 09:32 PM.
          Never stop learning
          Basic LCD TV and Monitor troubleshooting guides.
          http://www.badcaps.net/forum/showthr...956#post305956

          Voltage Regulator (LDO) testing:
          http://www.badcaps.net/forum/showthr...999#post300999

          Inverter testing using old CFL:
          http://www.badcaps.net/forum/showthr...er+testing+cfl

          Tear down pictures : Hit the ">" Show Albums and stories" on the left side
          http://s807.photobucket.com/user/budm/library/

          TV Factory reset codes listing:
          http://www.badcaps.net/forum/showthread.php?t=24809

          Comment

          • yobbgsm
            Senior Member
            • May 2017
            • 63
            • USA

            #6
            Re: Skyworth 40E58 no display

            @budm

            Will do and post result. Thank you for your patience.

            Comment

            • yobbgsm
              Senior Member
              • May 2017
              • 63
              • USA

              #7
              Re: Skyworth 40E58 no display

              This can be close. I resolved the issue, there is a single bulb that I think soon to be busted. It's on and off the reason there is a display sometimes.

              Comment

              • budm
                Badcaps Legend
                • Feb 2010
                • 40746
                • USA

                #8
                Re: Skyworth 40E58 no display

                When you finished the repair, make sure to turn down the Backlights level (not Brightness) to as low as possible to extend the life of the LEDs, these LED backlights are pushed to the limit so they burn out after a few years or less.
                Never stop learning
                Basic LCD TV and Monitor troubleshooting guides.
                http://www.badcaps.net/forum/showthr...956#post305956

                Voltage Regulator (LDO) testing:
                http://www.badcaps.net/forum/showthr...999#post300999

                Inverter testing using old CFL:
                http://www.badcaps.net/forum/showthr...er+testing+cfl

                Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                http://s807.photobucket.com/user/budm/library/

                TV Factory reset codes listing:
                http://www.badcaps.net/forum/showthread.php?t=24809

                Comment

                • heavymachines
                  Badcaps Legend
                  • Mar 2011
                  • 1028
                  • United States

                  #9
                  Re: Skyworth 40E58 no display

                  Thats what i did with the samsung we fixed yesterday the backlight setting was maxed out!!!! No wonder why it killed the bulb i replaced. and probably why it wanted to shut down on the replacement.

                  Comment

                  • autovolt007
                    New Member
                    • Nov 2017
                    • 2
                    • Philippines

                    #10
                    Re: Skyworth 40E58 no display

                    Originally posted by yobbgsm
                    Hi Experts,

                    I have a here, a 40" LED TV brand is skyworth, I thought it was a backlight issue since I can see a display using a torch. Voltage are good up to 37V output to LED. I opened it up and test all the backlight to find out nothing is busted. All are good. I rehot the TPS61196 Led dirver IC, assembled and test, seeing dispaly and I even the set the backlight but after closing the unit and boot up again, same issue occur, ni display again likeno backlight. Do you think the Led driver IC is the culprit? Voltage are good to the backlight. Any idea is very much appreciated.

                    Pics attached of the board.

                    sir i need a little help here, since you have that same board can you please take a look at the number of the smd transistor at the QP5 near opto? i got the same board and mine is bloated so i cannot see the number. this will be a very big help sir. thank you

                    Comment

                    • autovolt007
                      New Member
                      • Nov 2017
                      • 2
                      • Philippines

                      #11
                      Re: Skyworth 40E58 no display

                      this is my board sir skyworth 40e58, anyone here with a board like this i need a little help that one pointed in red arrow what is the number of it? thanks in advance
                      Attached Files

                      Comment

                      Related Topics

                      Collapse

                      • signal.quest
                        Panasonic LED TV TC-40A420U - Replaced Backlight LEDs but now no image/display or garbled
                        by signal.quest
                        I have a Panasonic LED TV TC-40A420U. The TV was given to me as an attempt to fix or throw out. I replaced the Backlight LEDs and now the screen lights up, but there is no image/display. If I play with the up/down buttons I can get the display to change from black to garbled. I can't get sound from HDMI but not sure of what input is selected. I have no remote control. When I connect a laptop to the HDMI ports it recognizes a Panasonic TV for display and sound output but I can't see or hear anything through the TV. This makes me think the mainboard is OK, but not sure if mainboard can...
                        03-17-2024, 10:14 AM
                      • lanovey
                        SF314-41 BIOS without internal display
                        by lanovey
                        Hello there,
                        I have a SF314-41 motherboard that i bought impulsively recently, the problem is that i only bought the motherboard only, nothing else. When i tried powering on the board with 19V (soldered on the DC IN port), and then shorting the pin 1-2 of the keyboard, the board is turning on (as indicated by the fan), however it seems like the board is displaying on the internal display as connecting to a display on the HDMI (external) does not display anything.
                        I tried connecting a USB keyboard, the keyboard is powered on, however pressing numlock do nothing (supposed to toggle...
                        06-13-2025, 02:38 AM
                      • Tynan Dill
                        Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                        by Tynan Dill
                        I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                        Upon bringing it home and plugging it up, it showed a standby light.

                        I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                        The screen seems to blackout and stay black, but with a flashlight I can see the display.

                        With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                        Assuming...
                        11-22-2024, 01:46 PM
                      • dbuergi
                        Acer XF240Y display backlight on and off then stays on but no display
                        by dbuergi
                        Hi all,

                        my display shows some strange bevahior. The backlight turns on, off and then stays on but i get no display or Acers logo. After some time it goes into standby. My notebook identifys the screen when i connect it by HDMI but i don't get an image.
                        Voltages seem n​ormal and the only possible problem i found is the cap on C33 on the tcom board. It shows 0 Ohm and 0V in diode testing. Any ideas for next steps or what i can check?...
                        11-14-2024, 04:36 AM
                      • MtapeK
                        820-01041-A Without BOTH internal display, And External and Backlight.
                        by MtapeK
                        Hello I have an 820-01041-A that does not have BOTH display and Backlight. The MBP was working properly to wake up without Display overnight. I have Tried SMC and NVRAM reset they both are not solving my Problem. The CapsLock on the KeyBoard, is working when you power it ON, and when you plug the Charger it's Responding with a sound that signifies the MBP has BOOTED in to SYSTEM. I have tried an HDMI (external Screen) its NOT Displaying anything. Also the INTERNAL Display Shows nothing.
                        1. I have Changed U9850 and the results are still the same, Discovered that the IC is working on a Good Known
                        ...
                        07-30-2024, 08:13 AM
                      • Loading...
                      • No more items.
                      Working...