-
-
Re: Eeprom dump thread!
Good morning all,
My TV brand TECHWOOD model TD22LED 13-2 main board VESTEL 17MB82-1a (ref 260912)
stay on standby red led indicator flashes
I am looking for the FIRWARES programs of the U10 and U12 eprom can you help me please
many thanksComment
-
Re: Eeprom dump thread!
T.MT8223.3B 10285 Can anyone share this firmware. ThanksComment
-
Re: Eeprom dump thread!
thank you very much for this quick response unfortunately the television is still on standby. Would you please have the firmware of the u10 and u12 eproms in .bin file
Thank youComment
-
Re: Eeprom dump thread!
Firmware for tv techwood TD22Led 13-2 vestel chassis 17MB82-1a ref 260912. I will test this firmware
Thank youComment
-
Re: Eeprom dump thread!
Ciao
Toshiba 26el 833
Main 32av833
Panel Lcn
ThanksComment
-
Re: Eeprom dump thread!
Hi,
I need Firmware:
Finlux/vestel
BOARD: 17MB95M
PANEL: VES400UNVS-S02
PS: 17ips71Comment
-
Re: Eeprom dump thread!
thank, thank!!Comment
-
Re: Eeprom dump thread!
hi anyone got digihome 40272sm eeprom Vestel 17IPS71Comment
-
Re: Eeprom dump thread!
Hello, I hope someone can help. I need EEPROM dump for Sony TV XBR-75X940D. Main board BM1 # 1-980-833-11 (173611611) dump needed for IC9017 (PIC16F527-I/SS) It is 20pin IC SSOP20. your help will be highly appreciated.Comment
-
Re: Eeprom dump thread!
Hello,
i need firmware for Toshiba 24W3753DG TV
Board: 17MB110P-pn 23451047
LCD: VES236WNTC-2D-N01
The TV only flashes red and green. Do you have recovery software for the specified TV? If possible, the installation procedure.
I can't find anything: - ((((Comment
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.07-26-2025, 03:24 PM -
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I...
Comment