Re: Eeprom dump thread!
i now understand thanks for advice
i now understand thanks for advice
-
-
Re: Eeprom dump thread!
hi can anyone help with dump for philips 65PUS6162,05
MB NUM:715G8709 MOE BOO 005N
maybe the same as 55inch model?
chassis TPM17.7E LALast edited by jimbofz; 03-31-2023, 10:17 AM.Comment
-
Re: Eeprom dump thread!
Chassis TPM17.7E LA or TMP17.7E LA ?.Comment
-
-
Re: Eeprom dump thread!
sorry its TPM i must remember to wear my glassesComment
-
Re: Eeprom dump thread!
jimbofz: in those Chinese tvs, if the only issue is no sound the problem is the sound amp, make sure the sound IC has power before replacing it, if no sound after replacing it then the issue is the microcomputer.Comment
-
Comment
-
Re: Eeprom dump thread!
many thanks for this dump
im having problem writing extracted .bin file to chip
my new chip is :st m24128b wmn6p
the ch341a programmer only has up to
m24c64 when you select manufacturer st from list
when i select atmel at24c128bi get
"chip memory with contents disagreement " message
can you advise pleaseComment
-
Re: Eeprom dump thread!
version 1.30Comment
-
Comment
-
Re: Eeprom dump thread!
Or thisComment
-
Re: Eeprom dump thread!
can you help looking for firmeware for a hisense h55m3300 can anybody helpComment
-
Re: Eeprom dump thread!
Do you correctly insert it (eeprom) into the programmer? Post a photo of how it's installed.Comment
-
Re: Eeprom dump thread!
it seems that if the chip is blank it shows
recognition error
i am now able to write to chip
but it only took a few seconds to write is that normal?
i expected it to take more time?Comment
-
Re: Eeprom dump thread!
Eeproms are written quickly, but there should not be a recognition error, most likely you have not recorded anything.Comment
-
Re: Eeprom dump thread!
Detect chip?Attached FilesComment
-
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.07-26-2025, 03:24 PM -
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I...
Comment