Re: Eeprom dump thread!
ELEFW505 has Full HD panel and ELEFW328 HD Ready. In service mode, you can not flip the image (mirror...)
ELEFW505 has Full HD panel and ELEFW328 HD Ready. In service mode, you can not flip the image (mirror...)
-
-
Re: Eeprom dump thread!
so the problem is the code from the ELEFW505Comment
-
Comment
-
Re: Eeprom dump thread!
that's very possible , I have been getting a lot of tv's lately where the owners have monkeyed around with them before they bring them in for repair.
so it's very possible they tried a firmware from another unit or something..
i guess the only way to know for sure is to get an actual dump from a working unitComment
-
Re: Eeprom dump thread!
OkComment
-
Re: Eeprom dump thread!
17mb110p Dumps.Comment
-
Re: Eeprom dump thread!
ok so i think? i found the issue with the element, but I'm not 100% sure.
I'm hoping someone can help with some panel pinouts..
I don't think this unit has the correct panel type, maybe there's no difference, i don't know
but i think the correct panel type should be V500HJ1-PE8 and not the currently installed panel V500HJ1-XR01
I cannot find panel info on either of themComment
-
Re: Eeprom dump thread!
Hi, I need dump for hyundai tv HY-LED39E9300
TP.VST59S.PB813
THANKSComment
-
Comment
-
Re: Eeprom dump thread!
Did you spell the TV model correctly - "HY-LED39E9300"?Comment
-
Re: Eeprom dump thread!
Done, try it.Comment
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.07-26-2025, 03:24 PM -
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I...
Comment