Eeprom dump thread!

[dadopo]

Thanks, I tried now the led lights up, flashes 3 times and then turns off, I have to check the mosfets on the board, thanks for everything

[lotas]

Like this.

[dadopo]

Thank you for your time, but where I change the status register I attach images of my programming software, thanks again

[lotas]

Good morning, I would need a good dump file for my samsung ue40mu6400uxzt, I attach the original dump.
Thanks in advance to anyone who can help me

Try your good dump file for your TV.

Don't forget to set and write the status register (0x88, 0x42) after writing the corrected dump.

[dadopo]

Good morning, I would need a good dump file for my samsung ue40mu6400uxzt, I attach the original dump.
Thanks in advance to anyone who can help me

[maxri]

hello, I would like to try again to solve the problem of my Samsung TV (UE49MU6220KXZT).
I have a Xggeku T48 programmer, can you confirm that with this device the programming of the bin file and the registers happens all at once?
Or is it necessary to repeat a second time for the status register?
Can someone provide another bin file to try?
Thanks.

[maxri]

Try it, don't forget about status register (0x88, 0x42).

With this file the led is now red and flashes when sending commands. The tv still doesn't turn on.
The processor heats up even if the tv doesn't seem to do anything.
I read the post about the registers and I hope I programmed the chip well.
Thanks anyway for your support.

[Drexter]

Your dump is ok, working, the problem is different.

Thank you very much I appreciate it!

[lotas]

Sorry I thought I uploaded it. Here it is. Thanks a lot!!

Your dump is ok, working, the problem is different.

[lotas]

Sorry... i forgot the file...

Try it, don’t forget about status register (0x88, 0x42).

[maxri]

I can check, but I don't see your dump.

Sorry... i forgot the file...

[Drexter]

Sorry I thought I uploaded it. Here it is. Thanks a lot!!

[lotas]

Hi. I have a Samsung UE49MU6220KXZT that won't turn on. No led and no response to commands.
Can someone check the dump or has the original , thank you

Board BN41-02568A BN94-12571E

Thank you.

I can check, but I don't see your dump.

[maxri]

Hi. I have a Samsung UE49MU6220KXZT that won't turn on. No led and no response to commands.
Can someone check the dump or has the original , thank you

Board BN41-02568A BN94-12571E

Thank you.

[Drexter]

Hello everyone, could someone help me check the bin file for a Samsung UN75MU6103. Ver. FB03. or if you have a working backup, would be greatly appreciated. The Standby led is turned off, still if joystick is pressed or powerd on by remote, it flashes, but nothing happens. All voltages are present and there is no short circuit on the board. Thanks in advance!.

[hazi12]

Yes, everything is possible, have the usb and hdmi ports been checked for short, low resistance relative to gnd?

Yes usb and hdmi ports fine, dc converters too, not found from the same board original firmware emmc nor w25Q40.

[lotas]

Thank you Lotas, is it possible that the failure was caused by the Emmc firmware?

Yes, everything is possible, have the usb and hdmi ports been checked for short, low resistance relative to gnd?

[hazi12]

Dump is ok.

Thank you Lotas, is it possible that the failure was caused by the Emmc firmware?

[lotas]

Hello, can someone check the dump or has the original , thank you

Samsung UE55MU6170UXZG KANT_M_BUILT_IN BN41-02568B BN94-12486N

It responds to remote on and off, but does not turn on 12V power for pmic.

Dump is ok.

[hazi12]

Hello, can someone check the dump or has the original , thank you

Samsung UE55MU6170UXZG KANT_M_BUILT_IN BN41-02568B BN94-12486N

It responds to remote on and off, but does not turn on 12V power for pmic.