Sanyo dp55441 "no signal" please help!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Georgia088
    Senior Member
    • Sep 2014
    • 109
    • USA

    #1

    Sanyo dp55441 "no signal" please help!

    I have a Sanyo dp55441. A lightning storm came by the other day and got several electronics in the house. This tv included. It wouldn't do anything when power was pressed. I took tv down, took back cover off, and visibly checked everything and nothing stood out. I plugged power up and tv came on. Everything seemed to work. I could change input and it would display and then show "no signal". So I connected it to different sources and still get "no signal". I have tried all hdmi ports. Composite Video ports and the USB port and they all show no signal.

    Any ideas?

    The main board's numbers are listed as 431c4169l02. They are nearly impossible to find.

    Questions:
    Do you think this is what is causingissue?
    Is there a way to check if this is bad?
    Is this part compatible with other similar parts?

    Thanks so much for any help!
  • Diah
    Badcaps Legend
    • Feb 2013
    • 6344
    • Germany

    #2
    Re: Sanyo dp55441 "no signal" please help!

    one test need to do, when you plug USB storage check the LED indicator of the USB it tun on and blinking or not, this test to confirm if 5 Volt there in the signal circuit.

    Comment

    • Moreno83
      Badcaps Legend
      • Jun 2014
      • 2008
      • The Netherlands

      #3
      Re: Sanyo dp55441 "no signal" please help!

      The mainboard probably took a big hit and the chip that controls the HDMI is not working.

      http://www.ebay.com/itm/Sanyo-55-DP5...-/161447837497

      $55 not a bad price! Its the L02 version. If all connectors look visibly the same then it will work.
      I only repair Panasonic plasma tv's! Currently owning a TX-P55VT50 and still searching for a ZT60!

      Comment

      • Georgia088
        Senior Member
        • Sep 2014
        • 109
        • USA

        #4
        Re: Sanyo dp55441 "no signal" please help!

        Thanks for the help!
        I plugged a usb into the port and it did light up. It also would allow me to access the usb info. However it still wouldn't show video through the hdmi or component ports. Any idea?

        Also, that link with the main board for $55 will be compatible if it looks the same even though the p/n isn't exactly the same?

        Thanks again for all your help!

        Comment

        • Diah
          Badcaps Legend
          • Feb 2013
          • 6344
          • Germany

          #5
          Re: Sanyo dp55441 "no signal" please help!

          let we narrow it more, did you play photo or movie or music via USB, we need to confirm the audio and video process at the main processor not damage.

          Comment

          • Moreno83
            Badcaps Legend
            • Jun 2014
            • 2008
            • The Netherlands

            #6
            Re: Sanyo dp55441 "no signal" please help!

            That board comes out of the same tv so it will work.
            I only repair Panasonic plasma tv's! Currently owning a TX-P55VT50 and still searching for a ZT60!

            Comment

            • Georgia088
              Senior Member
              • Sep 2014
              • 109
              • USA

              #7
              Re: Sanyo dp55441 "no signal" please help!

              Update:
              I put in usb and I can display a jpg image file. It will not show any of my MP4 video files on the usb to try to play them. Any ideas what video format the tv will play through usb?
              Thanks!

              Comment

              • Diah
                Badcaps Legend
                • Feb 2013
                • 6344
                • Germany

                #8
                Re: Sanyo dp55441 "no signal" please help!

                yes USB designed on this set of Sanyo play only Photos, nothings wrong with it, was my mistake to wrote music, video file.

                please read this link how to inter service ( Factory ) menu, and first focus on point No (8) Source Calibration of PC or YPbPr/YCbCr terminal signal ... if it give you OK will be good, if it give you result NG . then go to point No (6) NVRAM CLEAR. to rest the set complete.. as this set had much do with firmware to syncs HDMI and calibration them . also give it try, before you go to option change or inspection hardware.


                https://electro-medical.blogspot.de/...ode-power.html


                also please put it in mind don't blame only yours Sanyo TV of this fault, try to test yours HDMI out put source set. and HDMI cable too. to be sure that fault belong to the TV 100%.
                Last edited by Diah; 07-20-2016, 01:13 AM.

                Comment

                • Georgia088
                  Senior Member
                  • Sep 2014
                  • 109
                  • USA

                  #9
                  Re: Sanyo dp55441 "no signal" please help!

                  Ok. I followed the instructions from your link clicked source calibration, did a nvram clear and reset to default settings. I put tv on video 3 and pc and did source calibration and got "pattern ng" I changed to every source on the tv from different output sources and can't get anything to provide video or audio to the tv. From the usb I can display an image and all menu function work on the tv. What should I check next? Does this still sound like this is a main board issue?

                  Thanks again for all of your help!
                  Last edited by Georgia088; 07-20-2016, 08:23 AM.

                  Comment

                  • Diah
                    Badcaps Legend
                    • Feb 2013
                    • 6344
                    • Germany

                    #10
                    Re: Sanyo dp55441 "no signal" please help!

                    yes its main boards issue, did yours RF ( tuner ) working or also cut no signal ?

                    Comment

                    • Georgia088
                      Senior Member
                      • Sep 2014
                      • 109
                      • USA

                      #11
                      Re: Sanyo dp55441 "no signal" please help!

                      It is also no signal. Also, the link provided for the replacement board on eBay is a L01 version. Will this work as mine is a L02. If I find a L02 that comes out of same model tv as mine and looks identical it will work?

                      I really appreciate your help!!!

                      Comment

                      • Diah
                        Badcaps Legend
                        • Feb 2013
                        • 6344
                        • Germany

                        #12
                        Re: Sanyo dp55441 "no signal" please help!

                        Originally posted by Georgia088
                        It is also no signal. Also, the link provided for the replacement board on eBay is a L01 version. Will this work as mine is a L02. If I find a L02 that comes out of same model tv as mine and looks identical it will work?

                        I really appreciate your help!!!
                        you can try make for him offer moe cheaper.. and you know now how to deal with service men, so you can change any if the replacment boards need other settings...

                        .. i would suggest since you are going to change the MB, take it out from the set, and with hot air gun, heat the main processor very well , it may got bad soldering as the pins all downside.. try it if not go to replace

                        Comment

                        • Georgia088
                          Senior Member
                          • Sep 2014
                          • 109
                          • USA

                          #13
                          Re: Sanyo dp55441 "no signal" please help!

                          So, what you are saying is that all other versions that look the same as mine will work with my tv. I just may have to change the settings? In the factory mode service menu? Is this correct?
                          Thanks again!

                          Comment

                          • Diah
                            Badcaps Legend
                            • Feb 2013
                            • 6344
                            • Germany

                            #14
                            Re: Sanyo dp55441 "no signal" please help!

                            yes, also it may work direct with out need any change. .. of course if its not defect .

                            Comment

                            • Diah
                              Badcaps Legend
                              • Feb 2013
                              • 6344
                              • Germany

                              #15
                              Re: Sanyo dp55441 "no signal" please help!

                              between on ebay you can find yours version also new version 03..

                              you can see all HDMI line going to the IC in the middle, this one heat it with hot air gun... give it try and save $

                              Comment

                              • Moreno83
                                Badcaps Legend
                                • Jun 2014
                                • 2008
                                • The Netherlands

                                #16
                                Re: Sanyo dp55441 "no signal" please help!

                                The heatgun trick will not work. It only works when the chip became so hot that the soldering got loose.

                                This particular set has been struck by lightning. Or atleast a high current went through ( probably ) one of the devices that were connected via hdmi. The chip that controls the hdmi is shorted and needs replacing. If that is too difficult then replace the mainboard.

                                You can always try what Diah says as that would save you a lot of money but with high current through the mainboard im sure it will never work. Im sure that one OR more chips on the board are fried.
                                Last edited by Moreno83; 07-20-2016, 12:47 PM.
                                I only repair Panasonic plasma tv's! Currently owning a TX-P55VT50 and still searching for a ZT60!

                                Comment

                                • Diah
                                  Badcaps Legend
                                  • Feb 2013
                                  • 6344
                                  • Germany

                                  #17
                                  Re: Sanyo dp55441 "no signal" please help!

                                  Dear Moreno83, the IC not shorted, because it succeed to switched USB and display its contents, if he got Lighting from HDMI , you can see on the MB all HDMI line going direct to the IC. there is also big possibility one pin under the IC cracked by spark. since he should go to replace the boards,, any try will cost him Zero.

                                  Comment

                                  • Moreno83
                                    Badcaps Legend
                                    • Jun 2014
                                    • 2008
                                    • The Netherlands

                                    #18
                                    Re: Sanyo dp55441 "no signal" please help!

                                    No hard feelings Diah , i get your point but with lighting atleast 1 chip gets shorted. It will take more parts with him

                                    Hope a reflow will work! Fingers crossed.
                                    I only repair Panasonic plasma tv's! Currently owning a TX-P55VT50 and still searching for a ZT60!

                                    Comment

                                    • Georgia088
                                      Senior Member
                                      • Sep 2014
                                      • 109
                                      • USA

                                      #19
                                      Re: Sanyo dp55441 "no signal" please help!

                                      So is there a way to test and see what part is bad with a multimeter?
                                      Thanks again!

                                      Comment

                                      • Georgia088
                                        Senior Member
                                        • Sep 2014
                                        • 109
                                        • USA

                                        #20
                                        Re: Sanyo dp55441 "no signal" please help!

                                        Ok. Unfortunately the heat gun didn't fix problem. Still get pattern ng. Is there a way to test to see if and which chips or boards are bad?
                                        Thanks!

                                        Comment

                                        Related Topics

                                        Collapse

                                        • AstutePauciloquent
                                          Requesting Help For GA-970A-DS3 rev. 1.0, No Post code, no RSMRST# signal
                                          by AstutePauciloquent
                                          Hi everyone, over the past few months i have taken a deep dive into motherboard diagnostics and I love the challenge. Currently im trying to learn all about the signals that travel around the motherboard, such as frequencies, enable signals High and Low logic states etc. And i have been learning to read and using the Schematics for this board that i requested here on Badcaps forum, from a few months ago, this is such a great place for these.

                                          I’ve been working on a GA-970A-DS3 (rev. 1.0) that does not post. This motherboard has been my main learning board. I would like share...
                                          11-23-2023, 11:02 PM
                                        • howardc64
                                          Vizio M65Q7-H1 Red Vertical Strips fixed by tape blocking LC1 signal to half of the panel
                                          by howardc64
                                          Failure Symptom



                                          No picture, just red vertical stripes. Google search shows quite common problem for these recent Vizio M series although red vertical stripe pattern may differ. Some call it "Netflix" boot screen haha.

                                          Where is the short?

                                          Panel has 4x buffer boards. Quickly found the 1/4 panel buffer board with the problem by selectively disconnecting buffer board flex cables.



                                          Having recently fixed another Vizio with similar symptoms that was a shorted ESD diode array ( link ) Probed the ESD diode array but...
                                          05-27-2025, 02:56 PM
                                        • karthur
                                          Sanyo DP55441 - No brightness control
                                          by karthur
                                          Recently picked up a Sanyo DP55441. Set has a few issues:
                                          1. When I turn it on, I always have to select either "Store" or "Home" on the menu (see attachment).
                                          2. It forgets which input I was using last, so I have to change the input setting everytime.
                                          3. The controls for Brightness, Contrast, Saturation, Hue and Sharpness are not available from the menu (see attachment).

                                          Besides these issues the set works good, no other issues that I know of.

                                          I am thinking all three are related and its probably the main board. I have looked...
                                          06-19-2022, 08:09 AM
                                        • JayPoorJay
                                          Converting +/- 5v to a Usable Hz Signal
                                          by JayPoorJay
                                          Good morning.

                                          I have posted here before and have gotten AMAZING advise (thank you!). I'm back for more. This BCaps Sub Forum is so well attended I thought I would post here.

                                          This question is for an automotive application but has to do with what are essentially electrical questions and problem solving... If this is inappropriate I get it. Feel free to delete it or move the question.

                                          The V 12 Jaguar XJS is notorious for overheating in stop and go traffic in hot weather... Y'all will be potentially helpinh a LOT of people. The solutions and directions...
                                          08-07-2022, 08:35 AM
                                        • Scruit
                                          What is a normal composite signal range for a C64?
                                          by Scruit
                                          Hello all,


                                          Working on my first C64 / Breadbin / 250407. Purchased as non-working. Getting black screen.


                                          More detail below, but for those that want to get right to the question.... Here are a few waveforms comparing the Pin15 output on the VIC chip (luma/sync) to the pin 4 on the AV socket (composite signal).

                                          https://imgur.com/gallery/PpqcqPY


                                          My question is: Is the composite waveform range of 0.1v-1v too low for a c64?



                                          More detail:


                                          Symptoms are that that I get...
                                          04-28-2022, 05:33 AM
                                        • Loading...
                                        • No more items.
                                        Working...