50ps60

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tvtimmy
    Badcaps Legend
    • Mar 2015
    • 1160
    • usa

    #1

    50ps60

    Im looking at a buddys lg 50ps60. He said it wont turn on. I got it and it turns on, but the display is dim.
    When menu is on, the middle third of screen is clear( but dim and fuzzy ), and the left and right thirds have red transparent vertical segments, which match up with thee bottom buffers.
    I can get pics of everything if needed. Vsus and va are spot on.
    Does anyone know what the problem is?
    Grainny display makes me think zsus, but whats with the red segments?
    I will leave it to THE PROS here. Thanks.
  • ReeceyBurger123
    Never Give Up !
    • May 2014
    • 7325
    • Britain

    #2
    Re: 50ps60

    Yes Zsus issue.
    Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

    https://www.facebook.com/Telford-Tel...7894576335359/

    Comment

    • tvtimmy
      Badcaps Legend
      • Mar 2015
      • 1160
      • usa

      #3
      Re: 50ps60

      Thanks R.B.

      Comment

      • ReeceyBurger123
        Never Give Up !
        • May 2014
        • 7325
        • Britain

        #4
        Re: 50ps60

        No problem, normally on them if its the board Im thinking of. Theres three transistors and 2 resistors that need to be changed to fix it.
        Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

        https://www.facebook.com/Telford-Tel...7894576335359/

        Comment

        • tvtimmy
          Badcaps Legend
          • Mar 2015
          • 1160
          • usa

          #5
          Re: 50ps60

          I will check#'s tonight when I get home from my favorite watering hole, unpluged of course. Thanks again.

          Comment

          • tvtimmy
            Badcaps Legend
            • Mar 2015
            • 1160
            • usa

            #6
            Re: 50ps60

            Got a zsus board today. Put it in screen lit up brighter than before, still has red vertical cloumns on the outside(left and right) 2/3 of screen(transparent), then shuts off after 20 seconds.
            Screen still looks washed out .
            Might have a bad one. They do take returns.
            I can post any pics you need tomorrow, screen and boards.
            What do you think Reece?

            Comment

            • tvtimmy
              Badcaps Legend
              • Mar 2015
              • 1160
              • usa

              #7
              Re: 50ps60

              well.... bad news. Panel is blown. Gutted and packed up.
              I might have to wait at least a week or two to use them.....lol!!!!
              maybe two years, but, at least I have them. Thanks for the help!!!!

              Comment

              Related Topics

              Collapse

              • reessi
                LG Plasma ZSUS Flashing Screen, No Booting! - 50PB690V
                by reessi
                Replaced Zsus beginning of year as most transistors were short stopping tv powering up.

                Now screen flashes on off continually and ZSUS ticks. Looking like replacement maybe faulty or could something else cause it to shut down.

                If I remove both tabs from ZSUS to screen but keep all other connectors to ZSUS on then TV boots properly but screen very dark without ZSUS output, no ticking from ZSUS. So it only shuts down when under load from screen.

                If it is ZSUS then how to fault find, I already looked for shorts. No transistors shorted or caps and its...
                12-13-2017, 01:18 PM
              • alfredomfr1
                TV Plasma LG 60PN5000 ZSUS 15v missing
                by alfredomfr1
                All Voltages are OK except ZSUS 15v.
                YSUS board disconnected still 15v missing.
                ZSUS was replaced: 15v missing.
                Any help will be appreciated...
                04-29-2022, 11:26 AM
              • Salvatore057
                plasma TV Lg 42w451 - why is the zsus igbts damaged when the ysus is plugged?
                by Salvatore057
                Hi all,
                I am trying to fix my plasma TV which is not powering on due to damaged IGBTs. I have changed two igbts and 2 IC drivers on the zsus and also two igbts on the ysus.
                Now everytime I plugged the ZSUS and the YSUS boards to the power board, the two 30f124 IGBT on the ZSUS are damaged and the TV stays in standby mode. When I plug the ZSUS board alone the TV turns ON but I do not see pictures. When I plug the ZSUS board without the two 30f124 IGBTs and the YSUS board, the TV powers on with a picture.
                I am lost, should I change the YSUS board? Is the YSUS board damaging...
                04-29-2018, 01:29 PM
              • JDC
                LG 60PB6650 - Bad ZSUS (3.8v to YSUS instead of 16v)?
                by JDC
                Make and Model: LG 60PB6650-UA
                Issue: Turns on, no backlight, can hear static (no channel)

                I've been repairing TVs for a couple years now. I know how to use a multimeter for the most part and know how to test most components for shorts.

                The power board connects to the ZSUS and then connects to the YSUS. The ZSUS is where I believe the failure is because the 16v line is only 3.8V, even when I disconnect the ZSUS from the YSUS.

                This particular model seems to have a common failure with its YSUS. My goal earlier was to prove the YSUS was bad so I could...
                09-13-2018, 02:12 PM
              • JarrodHook
                LG 60PZ570 - Zsus replaced, still have issues
                by JarrodHook
                Hi everyone,

                I have had a interest in electronics forever, and as a hobby have tinkered with repairing things, taking them to bits, and so forth.

                However, I have a LG 60PZ570 that is causing me to rethink my life!!

                I purchased it for $100 as it had no picture, got it home, and it has the classic ZSUS issue, where in the picture is splotchy and dark.

                I checked the ZSUS board and determined there were a few blown transistors, fuses, etc.

                I looked up the repair kits, but the $70 shipping fee was a bit steep for me (I live in New Zealand)...
                03-17-2017, 09:53 PM
              • Loading...
              • No more items.
              Working...