Lg 60pc1d-aa

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • wozzie
    Member
    • Dec 2014
    • 21
    • Australia

    #1

    Lg 60pc1d-aa

    Hope some one can lead me in the right direction .
    I was given an Lg 60PC1D-AA Plasma tv i was told it had sound put no picture .
    Problem is the Y Sus board , have found Q24 sum45n25 shorted and two resistors that are open R250 and R251 i think they are 1R5 not sure if some one could help me with the resistor numbers it would be great . Have tested all the fuses which are every where and testing all the low ohm resistors . If i have missed any thing it would be much appreciated if you could suggest any thing else that might need to be replaced . Can those resistors be replace with normal resistors ?
    Thankyou
    Regards John
  • dick_barton
    Badcaps Legend
    • Aug 2015
    • 6642
    • Wales

    #2
    Re: Lg 60pc1d-aa

    Hello John,
    Any photo's of the back of the set showing the boards. Nice sharp pictures are always helpful.
    Willing to help but I'm no expert.

    Comment

    • mmartell
      Badcaps Legend
      • Oct 2013
      • 3189
      • Canada

      #3
      Re: Lg 60pc1d-aa

      These have ipm's that routinely short or even fail open. I would be surprised if that wasn't the case here as well.

      Comment

      • wozzie
        Member
        • Dec 2014
        • 21
        • Australia

        #4
        Re: Lg 60pc1d-aa

        These are pictures of Ysus board . Hope this helps ,ill try and take a picture of the back of the set with out the board .
        Attached Files

        Comment

        • dick_barton
          Badcaps Legend
          • Aug 2015
          • 6642
          • Wales

          #5
          Re: Lg 60pc1d-aa

          The IPM module's are under heatsinks and may have legends alongside. Can you measure the resistance from any of the supply pins given on them ( maybe 5v, 15V, Vs) to ground to see if you have a short circuit.
          You could also check the Mosfets and see if there is a short between any of the 3 pins.
          Willing to help but I'm no expert.

          Comment

          • Alastair E
            Chief Womble
            • Mar 2013
            • 1963
            • U.K.

            #6
            Re: Lg 60pc1d-aa

            Wozzie's Y-SUS Doesnt Have IPM's....
            --Its the slightly later, discrete type...
            TELEFIX

            How PLASMA SCREENS WORK, X-SUS and Y-SUS what they do--
            http://www.irf.com/technical-info/appnotes/an-1088.pdf
            PLEASE DO NOT EMAIL ME PRIVATELY FOR REPAIR ADVICE. QUESTIONS BELONG ON THE FORUM!

            Comment

            Related Topics

            Collapse

            • TinkerTron
              Schematic vs. Reality: Where Are the Resistors on My Sharp Clock Radio? Model FY-70CH
              by TinkerTron
              Hey everyone,

              I'm currently working on a mid-70s Sharp Electronic Digital Clock Radio, Model FY-70CH. I found the service manual online, printed it out, and have been studying it for a while. My main reasons for tackling this are: (1) I want to learn electronics and figured I'd start with something I had on hand, and (2) I want to fix its issues. Right now, the radio sounds awful, has about 5V DC at the speaker terminals, and the alarm time setting doesn't work. But I'm not asking how to fix these problems.

              Instead, here's what's been bugging me so far:
              The schematic...
              03-06-2025, 02:03 PM
            • brightest_z
              Hot Air Blew Away Resistors Near Bios
              by brightest_z
              Hi All - I'm in the midst or reprogramming the bios on my gen1 Surface Laptop Studio and I accidentally blew away 2 resistors nearby the bios. I don't have another board to measure values of the missing resistors and schematics aren't available, bbut the bios is a 6x5mm Winbond WSON8, W25R256JWPQ model. The traces are conductive to Pins 3 and 7 (IO2 & IO3 respectively) so I have reason to believe they are 10k pull up resistors since IO2&3 pins are used for Quad SPI instructions.

              Does anyone with more knowledge, and experience than I, know if this is the case?

              ...
              12-11-2024, 08:34 PM
            • jinu_j
              LED driver circuit. Burnt Resistors
              by jinu_j
              Hi Folks
              This has to do with a LED light driver rated for Output - DC36-65V 300mA. This is used to drive a 15W LED panel light.

              Now this does not work so opened up and found 2 resistors burnt to crisp. Sensing a learning moment, i looked around the circuit to figure out that it is built around the OB2538 chip. The circuit to a large extent follows the sample application circuit mentioned in the data sheet. I have traced the actual circuit and the same is also attached for reference.

              But i have some queries on this circuit
              1. The resistors that burnt to crisp...
              08-26-2020, 01:24 AM
            • repair-it
              Pioneer VSX-40 ,Trying to ID these resistors
              by repair-it
              I am trying to determine why these two resistors are the colors that they are. This is a Pioneer amp. The ones I am concerned about are the RED & GREEN colored resistors. I need to replace them and want to be sure to use the properly rated component....
              12-16-2024, 02:08 PM
            • BustinCaps
              Dell 2007WFP resistors under white silicon blog
              by BustinCaps
              My beloved 2007WFP just died on me. It has a green blinking light that just cycles through various display numbers. For a while I noticed it would blink slightly like the refresh rate was off. Nothing I have done has been successful in turning it on. So I took it apart and looked at the USB board since many people have had problems with the resistors under the silicon blob. I looked at the various other boards for the obvious signs such as blown caps, bad fuses, burn marks etc. Nothing looked obvious. I also checked most of the caps with an ESR meter and they checked out good.

              ...
              04-29-2022, 06:19 PM
            • Loading...
            • No more items.
            Working...