Lg plasma tv will not power up. 60pc1d

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

Check the Sus output from the Ipms.

IPMS? im not sure what that is and where the sus output is located? Greenpea!

[ReeceyBurger123]

Re: Lg plasma tv will not power up. 60pc1d

Wait hang on have you tried running the test patterns ?

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

check the sus output from the ipms.

ipms? Where is the sus output? Rookie here need guidance!

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

Wait hang on have you tried running the test patterns ?

ROOKIE HERE. How do I check the test patterns? Thx so much for your help.

[ReeceyBurger123]

Re: Lg plasma tv will not power up. 60pc1d

Check on google how to run Lg plasma test patterns. You might need to remove the mobo to do this though as you will need to access the control board.

[tom66]

Re: Lg plasma tv will not power up. 60pc1d

When you are reading "1" on the Vs pins, what mode are you using, and what range?

[ReeceyBurger123]

Re: Lg plasma tv will not power up. 60pc1d

When you are reading "1" on the Vs pins, what mode are you using, and what range?

Think it was in diode mode so basically OL. I think.

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

When you are reading "1" on the Vs pins, what mode are you using, and what range?

yea in diode mode. I am using a non audible DVM so 1 I believe is the same as OL.

[mmartell]

Re: Lg plasma tv will not power up. 60pc1d

There must be an ohms mode on your meter. It doesn't have to beep, just write down the readings.

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

There must be an ohms mode on your meter. It doesn't have to beep, just write down the readings.

OK this is what I have for the readings.
My DMM IS set on DCV. 200
The sticker on the TV shows; VA=60V...... VS =193V
there are 3 VS LOCATIONS. I plugged the tv in and it clicked twice on and twice off. I measured the 3 VS locations and they were all over the place.
130 down to 88.
The stndby locations all measured 4.9.

NOTE; If I leave the tv plugged in, it continuously cycles 2 clicks ON, 2 clicks OFF.
I unplugged the YSUS and I had 2 clicks and then NOTHING ELSE. I can press the power button and I get 2 clicks and NOTHING ELSE.
What NEXT?

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

Check on google how to run Lg plasma test patterns. You might need to remove the mobo to do this though as you will need to access the control board.

OK this is what I have for the readings.
My DMM IS set on DCV. 200
The sticker on the TV shows; VA=60V...... VS =193V
there are 3 VS LOCATIONS. I plugged the tv in and it clicked twice on and twice off. I measured the 3 VS locations and they were all over the place.
130 down to 88.
The stndby locations all measured 4.9.

NOTE; If I leave the tv plugged in, it continuously cycles 2 clicks ON, 2 clicks OFF.
I unplugged the YSUS and I had 2 clicks and then NOTHING ELSE. I can press the power button and I get 2 clicks and NOTHING ELSE.
What NEXT?

[clublex]

Re: Lg plasma tv will not power up. 60pc1d

When you are reading "1" on the Vs pins, what mode are you using, and what range?

OK this is what I have for the readings.
My DMM IS set on DCV. 200
The sticker on the TV shows; VA=60V...... VS =193V
there are 3 VS LOCATIONS. I plugged the tv in and it clicked twice on and twice off. I measured the 3 VS locations and they were all over the place.
130 down to 88.
The stndby locations all measured 4.9.

NOTE; If I leave the tv plugged in, it continuously cycles 2 clicks ON, 2 clicks OFF.
I unplugged the YSUS and I had 2 clicks and then NOTHING ELSE. I can press the power button and I get 2 clicks and NOTHING ELSE.
What NEXT?

[Alastair E]

Re: Lg plasma tv will not power up. 60pc1d

Repeating the Same Post--Three Times--Isnt going to make replies ANY faster!!

Check for faulty IPM's...