Toshiba 58L9300U 4K 3D HDTV

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ljintexas
    LJinTexas
    • Jan 2015
    • 669
    • USA

    #1

    Toshiba 58L9300U 4K 3D HDTV

    At first I had a red LED in the lower right corner. Left it powered up for an hour or so..now when I turn on, I get green LED and some sound out of the speakers like static. I have green LED heartbeat on far right board that looks like main board. Flashing three times, over and over. I also have green LED on far left board with large heatsink..looks like a digital board. From time to time, LED is flickering like it is communicating. I checked labeled voltages on the smps and all seem to be present. I have not uncovered what I think is an LED driver board on upper left. My first foray into a 4K set. No display or backlight as of yet.
    Attached Files
  • ljintexas
    LJinTexas
    • Jan 2015
    • 669
    • USA

    #2
    Re: Toshiba 58L9300U 4K 3D HDTV

    No ideas as to where to look next? There is a 9 pin comm port labeled Service. I may try hooking a laptop up to it just for kicks.

    Comment

    • Hamie
      Badcaps Legend
      • Apr 2014
      • 1383
      • UK

      #3
      Re: Toshiba 58L9300U 4K 3D HDTV

      Have you tried unplugging the tcon and turning on the tv?

      Comment

      • ljintexas
        LJinTexas
        • Jan 2015
        • 669
        • USA

        #4
        Re: Toshiba 58L9300U 4K 3D HDTV

        No sir, but I will. I think I have found an issue with the upscale board which fires the backlight. Looks like someone has tried to repair it..the leads(two yellow leads) from it to the LED Driver board had been pinched and were almost completely severed. I cut them clean and soldered them back together. Now I have continuity in both leads from connector to connector. Please see attached pics of someones attempted repairs. From back panel, looks like something hit this set, pinching the leads and possibly knocking these components loose.
        Other than having a massive power supply and an upscale board with mucho more interior communication, this set is much like a normal lcd. I do have 24 volts from smps at all of the caps on the LED Driver board, just no fire up signal on the two yellow leads..
        Attached Files
        Last edited by ljintexas; 10-21-2015, 06:54 AM.

        Comment

        • ljintexas
          LJinTexas
          • Jan 2015
          • 669
          • USA

          #5
          Re: Toshiba 58L9300U 4K 3D HDTV

          Tried disconnecting output of tcon..no lights..reconnected..tried input..no lights. Upscale board should be here today.

          Comment

          • ljintexas
            LJinTexas
            • Jan 2015
            • 669
            • USA

            #6
            Re: Toshiba 58L9300U 4K 3D HDTV

            Well, the upscale board was the issue. As soon as the panel energized, I saw cracks that were not visible before. I examined the panel with a light and there were no visible cracks. This set had signs it was hit from the rear..I am now the owner of a full set of good boards for a 4K Toshiba. Yay me!
            Attached Files

            Comment

            Related Topics

            Collapse

            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              11-22-2024, 01:46 PM
            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • Document Archive
              Toshiba Satellite Pro C660-1NQ Specification for Upgrade or Repair
              by Document Archive
              This specification for the Toshiba Satellite Pro C660-1NQ can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the C660-1NQ boardview and C660-1NQ schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download for Toshiba...
              09-06-2024, 05:27 AM
            • atltechnology
              Toshiba Satellite L50 PSKXWA-01100M Schematic Diagram Board View
              by atltechnology
              I need the Toshiba Satellite L50 PSKXWA-01100M

              This is my board no : daobltmb8fo rev f
              model no : Toshiba L50D-C
              Part no : PSKXWA-01100M
              Give me Schematic Diagram Board View
              01-14-2025, 04:21 AM
            • lostone
              Looking for help with a Viewsonic VP230mb where the backlight comes on only momentarily
              by lostone
              Hello, I came here after finding some similar questions asked on other monitors and hope someone here can help me get an ancient Viewsonic VP230mp (23" 4:3 LCD) back to working condition.

              First a little background, I have a background in computer and electrical engineering, and I'm smart enough to know I know nothing about LCD displays and how they work. For this topic I'm as green as they come.
              When the display is turned on the viewsonic logo displays in the uppper left for 2 seconds then the screen goes black, the power LED is green (on) and when a computer is connected...
              05-19-2024, 11:40 AM
            • Loading...
            • No more items.
            Working...