Pn42a450p1d

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • ljintexas
    LJinTexas
    • Jan 2015
    • 669
    • USA
    #1

    Pn42a450p1d

    No standby..totally dead. Found F801 and FS801 fuses blown, MOSFETs Q801 and Q802 shorted. The IC that drives the MOSFETs, U804, has several pins grounded that should not be according to fact sheet. Also found several bad diodes nearby. Did something else cause this or is this normal wear and tear on the SMPS for an 8 yr old plasma?
    Thanks
    Attached Files
    Tags: None
    • ReeceyBurger123
      Never Give Up !
      • May 2014
      • 7325
      • Britain
      #2
      Re: Pn42a450p1d

      You might want to consider replacing the primary filter caps, ive had a similar issue where the primary caps dry out which blows the pfc diode which blows the main transistors and there respective ic's.
      Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

      https://www.facebook.com/Telford-Tel...7894576335359/

        Comment

        • ammarben
          Senior Member
          • May 2013
          • 63
          • algeria
          #3
          Re: Pn42a450p1d

          give us the model of power supply BN44...

            Comment

            • ammarben
              Senior Member
              • May 2013
              • 63
              • algeria
              #4
              Re: Pn42a450p1d

              U804 mc33067 pin15 vcc ,pin 4,13 gnd

                Comment

                • ljintexas
                  LJinTexas
                  • Jan 2015
                  • 669
                  • USA
                  #5
                  Re: Pn42a450p1d

                  BN44-00206A
                  According to the specs on the IC it's rated for 150 deg F..
                  Main filter caps are barely in spec for capacitance. Pass ESR test easily.
                  I bet you are correct. By the time I buy all needed components with frieght, I will spend $40
                  I can get a replacement with one year guarantee for $45.

                    Comment

                    • ljintexas
                      LJinTexas
                      • Jan 2015
                      • 669
                      • USA
                      #6
                      Re: Pn42a450p1d

                      I took the main filter caps out of circuit..One passed ESR and capacitance both. The other one failed both tests. You were right on the money Reecey!
                      I ordered the replacement board with freight it was $53.

                      Thanks for your advice!

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • BlackScreen_22
                          Harman Kardon sub TS11 (ds15 amplifer) blows fuse and mosfets
                          by BlackScreen_22
                          Hi, I'll start by saying that I'm not an expert and I've reached a point where I don't know what to try/do anymore...
                          Starting from the beginning: I opened this subwoofer for the first time with a very strong smell of burnt electrical components, I realize that on the amplifier board there is a hole between V+ OUT and GND about the size of a finger, the damaged components were the shorted mosfets, two damaged zener diodes and two capacitors. I bought everything, I fixed the hole by cutting the pcb and putting a piece of a perforated board.
                          I had no problems connecting mosfets and capacitors,...
                          08-27-2024, 12:46 PM
                        • kotel studios
                          Intel D865PERL - no Vcore after replacing MOSFETs and MOSFET drivers
                          by kotel studios
                          Hi,

                          Finally got time to fix this board up.
                          At first it didn't give any POST codes. Turns out it was an unsupported Celeron D cpu. After dropping in an Celery 2.6gHz the CPU came out of reset with clock signal, but still no post codes. For a while it did work when I applied pressure to the ADP3168 chip, but on next reboot the MOSFETs started to burn. Then I left it as is for months.

                          Now I came back prepared. Replaced the bad MOSFETs and the ADPxx18k drivers. Now I don't get any MOSFETs blowing up issues anymore. But sadly, the Vcore is missing. The whole VRM isn't...
                          04-22-2025, 05:08 AM
                        • flerre
                          Gainward Phantom GTX 980 - mosfets w/ integrated driver NCP5369
                          by flerre
                          Hi!

                          Managed to get a Gainward Phantom GTX 980 in an auction for a bin with components.
                          No video out so I started fault finding and found a blown fuse for 3 mosfets. Started checking for shorts and found what I think is a short through all of those 3 mosfets; 0.1 ohms between "VIN" input and "VSWH" output. All mosfets in this gpu are the same ones (NCP5369) with integrated drivers and when I tried measuring the other ones through these ports they were somewhere in the kilo-ohms range.

                          So, could I safely assume all of these 3 mosfets are...
                          03-13-2022, 12:14 PM
                        • NanoTesting
                          Lenovo Ideapad 15IIL05, turns on and off with charger BUT works by injecting 20v after main mosfets
                          by NanoTesting
                          I got a 15-IIL05 that failed to turn on BUT IT DID TRY TO TURN ON and then turned off after 30+- seconds, i disassembled it and found a screw loose inside the case.
                          With charger it turns on, fan spins but gives no image.
                          Tested main mosfets no short, tested 3.3v,5v,DRAM, CPU etc and they were present.
                          Reflashed BIOS, same problem.
                          Replaced both main mosfets.
                          Checked main mosfets again and i noticed that they closed once the laptop shut down, so i decided to bypass them and used a bench PSU to check how much power the laptop was drawing while trying to turn on, 20v@3A,...
                          10-30-2024, 10:48 PM
                        • debruina
                          Pioneer VSX-859RDS with all mosfets gone
                          by debruina
                          Hi,

                          I am working on a pioneer VSX-859. It started with only one problem but i ended up with a lot more. Probably caused by me

                          Anyway it started with a DSP NG message on the display. That one was easy and was caused by a bad 5v rail. Replaced the capacitors and the message was gone. Everything seems to be working except for a blob sound every time i switched from source. Eventually i tracked that down to a leaking battery on the analog board. Repaired some via's and lines and everything worked ok. That same circuit also caused a not working DCdetect protection. ...
                          08-29-2023, 11:54 AM
                        • Loading...
                        • No more items.
                        Working...