Plasma Question.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pocketwatch62
    Senior Member
    • Jan 2013
    • 74
    • US

    #1

    Plasma Question.

    Is it bad to lay a plasma tv down to troubleshoot it?
  • ReeceyBurger123
    Never Give Up !
    • May 2014
    • 7325
    • Britain

    #2
    Re: Plasma Question.

    You need to be careful with them as if you flex the frame you could crack the panel, but as long as nothing is under the screen when you lay it flat it will be fine with power or no power going to the set.
    Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

    https://www.facebook.com/Telford-Tel...7894576335359/

    Comment

    • newtothis
      Badcaps Legend
      • Mar 2013
      • 1556
      • england

      #3
      Re: Plasma Question.

      Yes its fine, Its more about transporting TV's than anything.... If a TV is flat and is bounced up and down (Speed Bumps, Potholes etc) with the centre of the screen being the least supported area and will move up and down too... This can cause fracturing of the panel

      Comment

      • pocketwatch62
        Senior Member
        • Jan 2013
        • 74
        • US

        #4
        Re: Plasma Question.

        Thanks Guys!!

        Comment

        Related Topics

        Collapse

        • dclass-pro
          HP 440 G2 no power after short in flat lcd
          by dclass-pro
          Hi all guys, I need your help. On a HP 440 G2 - LA-B181P laptop I was changing the speakers and the pc worked fine everything ok.
          After closing it all with all the screws I realized that it would no longer turn on. I opened it and found that the flat cable of the LCD was shorted. I ordered a new flat but the motherboard still won't turn on, as soon as I connect the power supply the connector LED always flashes and the power button stays on.
          I tried to check the voltages and the 3v and 5v are there, on the battery pin (with no battery connected) I have about 2v.
          I tried to...
          08-11-2023, 07:47 AM
        • electricblue01
          Troubleshoot Samsung Plasma
          by electricblue01
          Hello newbie here.. My neighbor gave me a nice plasma to repair. PN69d660c1f.
          I found the power supply was bad. I tried to do component level repair but screwed up some traces. So , I bought a China (replacement board). The logic board blinks slow. The VS out of the PS is 319 and the VA is 5.1. When I test the vscan on the y board I have nothing. I replaced the y board and still nothing. The x board has 319. The Vs and Va are out of spec, so I emailed the company and they said it was better technology. ( not sure ?) I did not replace the y buffer board. Could that be why I still have...
          10-19-2020, 03:21 PM
        • reformatt
          A2337 not working with flat battery
          by reformatt
          Looking for some advice on a 820-02016 board as I don't have much experience with these M1 machines. Learning the nuances of them as I go.

          So the history of this machine was it had been in a bag where a bottle of water leaked. Presented as dead about a month ago, corrosion was mainly around the battery connector and it's sub-PCB. Some corrosion was noted on the board around UC300, CC325, CW1C7, CW1C8. That was it really.

          Now without battery connected, USB-C will stay at 5V and cycle between 0 and 120ma. PPBUS_AON is cycling between 0 to 12.3V. If battery is connected,...
          10-12-2023, 04:36 PM
        • ArMaaN376
          Samsung PS51E550 Plasma TV
          by ArMaaN376
          Hello,
          I am having Samsung PS51E550 Plasma TV. While the TV was working, a crackling sound heard & video went off with audio still ON. After switching it off & ON, the red LED on TV blinks six times & then off.
          Opened TV cover & observed foll
          a) Green LED on the small PCB blinks at @5-6sec ON & off for 3-4 secs. Red LED on logic board ON
          b)Vs & Va on power supply board raises momentarily to 209v & 58v resp & then drops.
          c) Cold test on Y-main board shows all 3 pins of FGPF4536 IGBT short to Grnd.
          How to confirm Y -Buffer board...
          06-19-2024, 04:05 AM
        • jm1234
          Panasonic plasma TX-P42ST50 - 6 blinks
          by jm1234
          Hi,
          anyone able to provide the service manual for old plasma Panasonic TX-P42ST50E?
          It turns off almost immediately (0~5 seconds after pressing the on/off button) and starts flashing the red diode 6 times.
          I disconnected the left-hand side board (SC?, both the ribbon cable and the power cable to it) and also another ribbon going to bottom left board. Then the led signal is 8 flashes. According to service guide to another Panasonic plasma it would mean the left-hand side board is faulty. But I'm not sure it 100% applies to my model.
          I checked that board for any obvious faults...
          05-22-2024, 06:59 AM
        • Loading...
        • No more items.
        Working...