Anybody know what the 2 blink code is for this model? My buddy said he accidently stuck his atenna wire in the tv where the main board is so it started sparking. Never worked since. I took it apart but i dont see anywhere on the power supply to measurre the readings, theres no board markings 5v,12v, etc....
-
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Photo of the back of set please so can see boards and layout.
Check Pin 1 on P7 connector on P-Board, What V do you get? -
Re: panasonic TH-42PX80U 2 BLINK CODE?
Attached FilesComment
-
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Also i have no voltage on that pin #1Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Ok check resistance from that pin to ground (Chassis)Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
SOS2 = 15V fault.
Generally 15V fault tends to trigger 10 blinks first. 2 blinks can occur if 15V collapses after set runs.
This is usually triggered by Vsus fault (shorted/low Vsus, or fault in thermal fuse detection block.) Check Vsus, if it rises then falls, or never rises at all, this can be indicative of this fault.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Tom sorry but all that stuff I don't understand.... New to this should I unplug some connections until I get a voltage on that pin? Also being all my friend did was touch the attena to the main board by accidentComment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Leave connections in place.
Set meter to 200 Ohms
Black Pin to chassis (Screw will do)
Red to Pin 1
What does meter read?Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
I had to set it to 2000 ohms and it says 940,Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
clear pic of this area from above pleaseAttached FilesComment
-
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Attached FilesComment
-
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
I need a closer pic of the area I highlightedComment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Attached FilesComment
-
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
Anyhelp?Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
?Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
I gave you info. Generally you're expected to have reasonable technical knowledge if you do a lot of TV's like yourself. So when I ask you to check VSUS, maybe do a little searching or look for the service manual before declaring that you can't do it.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: panasonic TH-42PX80U 2 BLINK CODE?
You should be looking around the area I had you zoom in on, You will see an adjuster pot there stating VSUS.... You want to find a test point for itComment
-
I recently got my hands on a 60" Panasonic P60ZT60 plasma tv (european model) that has some strange issues along with an 8 blink code.
It know this tv is getting old but it was once considered one of the best plasmas ever made, and i think it is still holds on to that even by todays standards.
So, long story short. When i first got the tv it had a very bright washed out picture with very raised blacks in all picture modes and i couldn't find the cause in the picture setting menus.
After doing a factory reset this problem was gone and the picture was back to...01-06-2025, 06:02 AM -
I aquired this Panasonic 60" plasma around the time my first child was born. It was meant to be a project tv, hoping to fix it chipping away at the repair in my free time. Well that was 2 years ago and i'm really just getting around to making a sincere effort to see if I can ressurect this beast.
The symptoms of the tv ar as follows:- Plug AC in to back of TV
- After about 2 seconds the relay on the P-sub board will click on and then a fraction of a second later it clicks back off
- The 3 blink code is given by the power LED
- If the TV is unplugged and then
-
My beloved Panasonic TC-P42ST30 has been stricken with the 14 blink code.
I've spent many hours reading through forums, watching YouTube videos and reading the Panasonic plasma troubleshooting guide. But I'm a novice at this, and still need some help to cross the finish line.
I understand the Panasonic troubleshooting guide suggests that the 14 blink code usually means there's a problem with either P-board or A-board. However, I also learned the problem frequently rests with the SN-board.
Using my multi-meter, I was able to confirm the P-11 pin on the... -
Hi All,
Thank you in advance for your advice.
I have a Panasonic Plasma tc-p55vt50 that's about 9 years old and has just recently stopped working :-(
I noticed that when I turn the tv on I hear a click then screen comes on for like half a second then shuts off and the led blinks 6 times.
I did some googling and found several video's on trouble shooting all sorts of blink codes. I finally came across one that showed 6 blink error code but for a different model. It recommended disconnecting the SC board to determine if it was the A board or power... -
ALL LCD LED TV SERVICE MENU CODES
Service Menu Code with Board Name
China Universal Board / Jumper Board Service Menu Code
Changhong Ruba Service Menu Code
Ecostar LED TV Service Menu Code
Orient LED TV Service Menu Code
Haier LED TV Service Menu Code
TCL LED TV Service Menu Code
Samsung LED TV Service Menu Code
LG LED TV Service Menu Code
Videocon LED TV Service Menu Code
Supra LED TV Service Menu Code
Toshiba LED TV Service Menu Code
Symphony LED TV Service Menu Code
Veste/ LED TV Service Menu Code...10-31-2024, 03:58 AM
Comment