TC-P50C2 Shattered Screen, want to be sure boards are OK to sell.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tw2005
    Badcaps Legend
    • Oct 2011
    • 6458
    • Australia

    #21
    Re: TC-P50C2 Shattered Screen, want to be sure boards are OK to sell.

    you might have to have a study yourself but the s2 has no link at P34 because of the soft start. The c2 has a link and a conventional on/off switch.

    so you may need to remove the link and then find the pads on the A board where that switch would be and short it out momentarily to boot it up.

    Comment

    • tw2005
      Badcaps Legend
      • Oct 2011
      • 6458
      • Australia

      #22
      Re: TC-P50C2 Shattered Screen, want to be sure boards are OK to sell.

      Originally posted by johnboy1313
      If I remember correctly, they were identical boards. Both had the AV suffix. I've been wrong before though.
      AV would be for C2 models, AC is for S2 and has soft start

      Comment

      • johnboy1313
        Badcaps Legend
        • Nov 2012
        • 1959
        • USA

        #23
        Re: TC-P50C2 Shattered Screen, want to be sure boards are OK to sell.

        I'm sure you're correct. Thanks for the heads up.

        Comment

        • johnboy1313
          Badcaps Legend
          • Nov 2012
          • 1959
          • USA

          #24
          Re: TC-P50C2 Shattered Screen, want to be sure boards are OK to sell.

          Just got off the phone with the buyer. He was a very nice gentleman who really knew what he was talking about. Turns out, it was not an issue with the main board, but an issue with the IR board. Apparently when that board was disconnected, he could jumper the TV on. Once that board was connected, the roughly 5V at the connector dropped to less than 2V and the TV was dead. He had to call Panasonic 4 times and finally spoke to someone that was familiar with the issue. They sent him a service bulletin. I've asked if he would forward it. I'll post it if he does.

          Comment

          • tw2005
            Badcaps Legend
            • Oct 2011
            • 6458
            • Australia

            #25
            Re: TC-P50C2 Shattered Screen, want to be sure boards are OK to sell.

            Originally posted by johnboy1313
            Just got off the phone with the buyer. He was a very nice gentleman who really knew what he was talking about. Turns out, it was not an issue with the main board, but an issue with the IR board. Apparently when that board was disconnected, he could jumper the TV on. Once that board was connected, the roughly 5V at the connector dropped to less than 2V and the TV was dead. He had to call Panasonic 4 times and finally spoke to someone that was familiar with the issue. They sent him a service bulletin. I've asked if he would forward it. I'll post it if he does.
            Sounds like a happy ending

            Comment

            Related Topics

            Collapse

            • Ryan.man
              Macbook 2017 with touchbar (A1706) won't turn on after removing the screen
              by Ryan.man
              Hello everybody! Posting this in hopes somebody has some expertise that leads to a clear path of troubleshooting that saves me a lot of time!

              My macbook has the flex cable problem, the one that prevents the screen turning on. Ive been dealing with this for the last 3 years. Last year it went dead and I managed to fix it following youtube tutorials. But my fix wasnt the best, the problem returned a month later. This week, it went dead again. I again tried to fix it.

              This time the original cable broke too close to the screen, it can't be fixed without tearing the screen...
              02-04-2025, 12:23 PM
            • smic717394
              iphone XS turns off when press on screen.
              by smic717394
              Hi,

              I have a iphone XS that came in for a screen replacement, the screen was badly cracked, and inside missing scues, on the back of the screen still the blue protector, the screen was a LCD. So we replaced the screen and all good, installed the screen and we noticed that pressing the screen with a bit of force but not excessive, the phone dies. After plugging the charger it turns back on, but again if you press it it dies. I open the phone again, and I can't see anything major, with the phone open, if I press on the logic board, battery, charging board, or even putting pressure on...
              07-25-2024, 10:16 AM
            • Chrissygizmo
              Samsung UE55JU6800K half screen dark
              by Chrissygizmo
              Hello everyone, I’ve just been given a Samsung UE55JU6800K smart tv as it had white spots on the screen due to the led lenses falling off. After refitting them & putting the tv back together I thought it was a nice easy fix for a free bedroom tv , then I tried it before screwing the back into place. I realised that the right side of the screen was darker than the other side, I removed the screen again as I thought the backlights had failed but they are fine.
              I put the screen back in place & turned it back on . The screen seemed to be ok again but different screens on the same...
              02-10-2025, 12:33 AM
            • spice_disc
              Vizio TV M50-C1 reboot cycle and static on screen
              by spice_disc
              I'm currently trying to diagnose and fix my Vizio TV (Model M50-C1). I've tried a number of different basic solutions, but I'm trying to determine if my issue is currently a failing panel, T-Con board, or main board (or something else entirely) and whether or not it is worth my time to fix it. Details of the issue and what I've tried are below as well as why I think it is either a bad panel, T-Con board, or main board.

              The Issue: The TV will be on and working fine but after the TV is on for ~5-10 minutes the screen will freeze (with sound continuing) until the TV reboots itself. While...
              09-08-2024, 02:37 PM
            • ipatch
              ipad pro 9.7" blew a SMD component while replacing the screen 🤦‍♂️
              by ipatch
              i have an ipad pro 9.7" (1st gen) A1674 where i replaced the screen, but never attached the screen to the frame/chassis (glued down) due to the ipad being previously dropped so the new screen would never fit in the frame properly. so i need flex/bend the chassis to eventually fix the new screen in properly. so i temporarily just applied blue tape around the edges of the screen to keep it in place. when watching videos with the ipad the screen started flicker, so i though maybe the new quasi cheap amz screen i purchased was going out. so i disconnected then reconnected with power still on,...
              08-24-2024, 02:36 PM
            • Loading...
            • No more items.
            Working...