Announcement

Collapse
No announcement yet.

lg ps3000

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #61
    Re: lg ps3000

    there you go tom and thats with beeper on
    Attached Files

    Comment


      #62
      Re: lg ps3000

      any clues ?

      Comment


        #63
        Re: lg ps3000

        Sorry I don't have any real suggestions because I can't explain those results at all.
        I suppose it could be one of those other ICs, but right now you are looking at maybe 4 ICs bad...
        That just doesn't happen, unless the panel is cracked or something else is badly wrong?
        Last edited by tom66; 03-11-2014, 04:09 PM.
        Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
        For service manual, schematic, boardview (board view), datasheet, cad - use our search.

        Comment


          #64
          Re: lg ps3000

          got new buffers today now beffor i fit them is it safe to fit or will thay blow again all readings r fine with both buffers out ?

          Comment


            #65
            Re: lg ps3000

            You would need a scope to be certain. If Vsc is OK it should be fine but I've never done one of these, mostly work on Panasonic...
            Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
            For service manual, schematic, boardview (board view), datasheet, cad - use our search.

            Comment


              #66
              Re: lg ps3000

              i fitted new buffers and got only half picture but they tested fine ? do you think that means fault on ysus ?

              Comment


                #67
                Re: lg ps3000

                Ysud can't cause that.
                Any connector between the two boards? If so make sure it's seated properly.
                Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                Comment


                  #68
                  Re: lg ps3000

                  ok will fit them again it was 3 1/4 of the screen had good picture the rest was black

                  Comment


                    #69
                    Re: lg ps3000

                    ok took them out and put back in now i have sound no pic but buffers still test fine

                    Comment


                      #70
                      Re: lg ps3000

                      Maybe post a good picture of the ysus and buffers installed as it is right now. Also might be worth checking none of the connectors or solder joints have fractured with all removal and installation of these buffers on both the buffer and ysus sides.

                      i have had one guy who broke a track on the ysus on a PQ30, it's a lot shot but everytime you touch it it seems you get a different result?
                      Last edited by tw2005; 03-12-2014, 07:59 AM.

                      Comment


                        #71
                        Re: lg ps3000

                        ok some pics still cant get a picture just sound how would i go about testing the ysus for faults
                        Attached Files

                        Comment


                          #72
                          Re: lg ps3000

                          What happened to 3/4 pic?
                          Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                          For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                          Comment


                            #73
                            Re: lg ps3000

                            I'm at a loss, but on the bottom of the ysus are the 3 grounding screws in place? Too blurry for my eyes to decide.

                            Comment


                              #74
                              Re: lg ps3000

                              Originally posted by tom66 View Post
                              What happened to 3/4 pic?
                              dont know what happen tom i check all plugs ect like you said then tried again then got black screen ive had them out 4 times now and still cant get the picture back all buffers still test fine but with tv on im not getting vy vsc only getting upto 36v ?

                              Comment


                                #75
                                Re: lg ps3000

                                Is that without the buffers? If you got half a picture, and picture was OK, the Y-sus is working. It gives the same drive waveform to both boards.

                                So it may have been a defective buffer board. Yes, that again. Cracked screen boards I'm assuming?

                                Which half of the screen not working: top half or bottom half? If bottom half, try running without bottom buffer.

                                On the other hand, if the same area of your buffer boards is failed, I'd start suspecting the panel - as rare as that might be, I suppose it's the only option left!
                                Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                Comment


                                  #76
                                  Re: lg ps3000

                                  its was 3/14 from left to right that had pic and was good picture but now its all black the buffers do test fine on a meter ? with buffers in the volts r gone i didnt want to remove buffers from the ysus as didnt know if i would blow them . so should i remove them from ysus then check volt reading again tom

                                  Comment


                                    #77
                                    Re: lg ps3000

                                    So TOP 3/14 of picture was OK?

                                    Then you can run set with bottom buffer removed only (top installed.) Check -Vy and Vsc in this condition. You may get picture on top half.

                                    You can run the TV with the buffers removed too, and check -Vy and Vsc in that condition.
                                    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                    Comment


                                      #78
                                      Re: lg ps3000

                                      no had picture from top to bottom but only 3/14 from right side looking at tv the left side was black

                                      Comment


                                        #79
                                        Re: lg ps3000

                                        ok so with both buffers out i get good volt readings with any buffers in i get same upto 36v ive tried 2 diffrent ysus boards and get the same thing on both ?

                                        Comment


                                          #80
                                          Re: lg ps3000

                                          Does anyone have a guid on how to test ysus and buffers on this model
                                          As the guy who fixed my buffers befor said just becase my
                                          Meter does not beep don't mean buffers r any good

                                          Comment

                                          Working...