Led TV Board Replacement, same part number and model, different size

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Cvrado
    New Member
    • Mar 2024
    • 4
    • Portugal

    #1

    Led TV Board Replacement, same part number and model, different size

    Hello my friends!
    I have a question that I think you can answer and help me with!

    I have a faulty main board from an led TV. And I found the same part number board and design but is from a 43" TV and I want to use it on a 65". On its stickers , all are the same except the wattage for the LEDs backlight, both state different watts and LED Voltages!

    So I presume that the backlight inverter section from the replacement board has lower wattage then the original one, am I right?

    My concern is that the board won't draw enough voltage to the backlight!​
  • Cvrado
    New Member
    • Mar 2024
    • 4
    • Portugal

    #2
    Even the components are all identical and the structure and design are the same .

    I only find a MOSFET that o presume it is a Jumper Junction Power MOSFET . Is the MOSFET responsible for a push up voltage? Or will the board manage for itself the necessary voltage to the backlight has the moment it is connected ?

    ​​​​

    Comment

    • Cvrado
      New Member
      • Mar 2024
      • 4
      • Portugal

      #3
      2 pictures are from my faulty board (65" led TV), and other picture is from the replacement board !

      Has it reads on it's label (150-165V) on 65" faulty board. And it reads (87-99V) replacement 43-50" board.

      I have been searching and one some they say that if the resolution is the same and part number and components structure is the same it will work!

      But on others they mention the eventually of a different DC to DC structure!

      The only difference I can spot by the picture is the on the inverter side of the board my bigger TV (150v backlight) have 3 big and same size capacitors and the other board has 1 big and other 2 smaller !
      Last edited by Cvrado; 03-02-2024, 05:19 PM.

      Comment

      • lotas
        Badcaps Legend
        • Jan 2016
        • 4455
        • Russia

        #4
        You will need to update, change the software for your panel via usb, (If it is possible to change it in service mode or through the console)

        Comment

        • Cvrado
          New Member
          • Mar 2024
          • 4
          • Portugal

          #5
          Hi lotas , thanks for the reply!
          So if I change the software version or check for screen size on the service menu the backlight driver will change its values to push up from 68V to 150V ? No need to change anything by hardware ?

          Comment

          • lotas
            Badcaps Legend
            • Jan 2016
            • 4455
            • Russia

            #6
            Here you also need to look at the position resistors in the backlight driver, current sensors, the number of the transformer (matches the other one), and the voltage on the capacitor (whether it matches the voltage should be 200v-250v)
            Carefully inspect this area for the nominal value and location of the resistors.
            Attached Files
            Last edited by lotas; 03-03-2024, 04:27 AM.

            Comment

            Related Topics

            Collapse

            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              11-22-2024, 01:46 PM
            • boosti45
              Macbook pro logic board replacement parts quesion
              by boosti45
              i have a 2020 macbook pro 13" A2251 with 820-09149 logic board so i found an issue with chip labeled U6903 according to schem. boardview using flexBV software, so i removed it from the board and the issue im having is that the chip says "07A08FI ELC180​" on top of it but when searching for a replacement chip, i can find tons of identical looking chips that also have "ELC180" printed on them but the first set of digits is never the same so im trying to find out if i need this exact chip with these same numbers as mine and if not which ones are compatible as a replacement?...
              08-21-2024, 05:23 AM
            • eum
              PSU Board repair or replacement Ecler Nuo 2.0 DJ mixer
              by eum
              Hi,
              I try to repair this fly-back type PSU, I diagnosed (identifiable) dead N-MOS and fuse, but there are 3 smd resistors on the bottom that burned and became unreadable.

              The support in charge of the brand in France managed to get me the schematics from Ecler, but it didn't include the PSU board. After a while they finally told me that the unit was too old so they don't have the PSU board schems.

              I can find replacement PSU board online, but only for the Nuo 3 or 4 or 5, and it seems they ar compatible with each other, as I often find boards compatible with these...
              07-28-2023, 03:05 PM
            • Hakuu
              LG OLED77G1PUA - No Video / Audio after a TCON Board change and Software Update
              by Hakuu
              Hi There,

              This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.

              After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.

              More Details

              TV Model - LG OLED77G1PUA

              Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt...
              07-12-2023, 02:37 PM
            • Loading...
            • No more items.
            Working...