i was here yesterday and tom66 had me go to manuals and check voltages .i did all but i dont have a scope but all other voltages check out fine any suggestions ?? pdp 42x32000 checked vs 184.7v va was 60v , vy -200 , vsc120 z bias was 99.7
-
-
Re: visio p42hdtvA10 no sound bad picture
Forgot pics !Attached Files -
-
Re: visio p42hdtvA10 no sound bad picture
Vscan should be reading in the negative range. 120 sounds lowDid I leave the soldering iron on?Comment
-
Re: visio p42hdtvA10 no sound bad picture
According to the sticker on the back of the panel , it says 120 for vsc and
-200 for -vy and the picture is flickering also .. ( the pics don't show it )...Last edited by fatboytp; 01-21-2014, 10:17 AM.Comment
-
Re: visio p42hdtvA10 no sound bad picture
I guess no more replys ? well thanks anyway ..Comment
-
I have a TCL 55P6US with sound and backlight but no picture. This model does not have a T-CON board, and the right (rear perspective) panel board is fed from the left panel board. I have not been able to induce any change by disconnecting the secondary panel board or the tape cut-off method on the primary board.
There are a bunch of voltages missing on the panel boards. I can't find any shorted caps of the panel boards, and all of the missing voltage rails read in the kiloohms, which leads me to suspect the issue may lie on the circuit board, rather than a short in the panel.
... -
Hi, I have a Samsung UE50TU with:
- sound and backlight, but no picture
- when it arrived, it had a picture for a few seconds
- it keeps rebooting
- without ribbon cable between the two panel boards, it does not reboot but I have no picture
- without cable between mainboard and lcd panel, it does not reboot (but obviously i have no picture)
- when i try a tape fix, its keeps rebooting, unless I tape off pin 1 (the innermost pin). In that case it does not reboot but I have no picture.
- without cable between mainboard and lcd panel and with a jumpered... -
I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started ‘fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.
I ordered a supposedly ‘new' Tcon board this time, and... -
Hello everyone,
Ive got a UE60KU6079 on the workbench that is giving me some headaches trying to troubleshoot.
The previous owner stated that there had been white dots on the screen which from the description sounded like some lenses fell of the backlight LEDs.
He had opened the TV from the back, trying to get to the backlight, supposedly gave up, reassebled everything and gave the TV to me.
I expected the worst like ripped COF cables or a cracked panel but could not find anything like that yet.
Anyway I still fully expect that there has been something seriously damaged... -
Hi all
I was just given a Samsung TV with the issue. I read various threads and videos and attempted the ribbon tape method to gain an image, but no luck.
Symptom:
No picture no sound.
When I plug in the power cord, Backlight LED turns on for a half second and then turns off. The red LED next to the power button located center bottom flashes 2 or 3 times. When the power button is pressed after, it does the same thing.
No sound at all.
What I tried:
1. I tried unplugging the left or right ribbon...
Comment