LG 50PC1D Recurring Ysus Buffer Short

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • alanos313
    Member
    • Jan 2012
    • 10
    • UK

    #1

    LG 50PC1D Recurring Ysus Buffer Short

    Hi,

    I have an LG 50PC1D plasma TV which suddenly lost picture, showing only an entire screen of moving coloured vertical lines. After a bit of research online, I found a post here http://blog.coppelltvrepair.com/2010...-lines-in.html which pointed to the YSUS buffers, specifically the MOSFETs which are mounted on them... I tested them as per the instructions on the page, and found two shorted FETs on the lower buffer. I replaced them, and the set worked perfectly, without any faults at all. For 30 minutes. Then the same problem returned.

    I checked the buffers again, and found that the third FET on the lower buffer had now shorted. So I replaced that one. Again, the set was perfect, this time for about 4 hours. Then it developed a thin vertical line on the right side of the screen, top to bottom. About 30 minutes later, another line appeared, on the left side, top to bottom.

    Around 30 minutes after that, the screen began to flicker on and off in roughly 1 second intervals, which is what happened just before it blew the FETs last time! I switched off and allowed it to cool down.
    I haven't checked yet, but I'm pretty sure I will find another shorted FET. Can anyone tell me what I can do to trace the cause of these shorts?

    Cheers
  • capkid
    Badcaps Legend
    • Oct 2010
    • 1339
    • United States

    #2
    Re: LG 50PC1D Recurring Ysus Buffer Short

    It sounds like your Y-Sus may be faulty. Check your voltages, including VS, VA, VSC, and -VY.
    LG Plasma Mal-Discharge Correction Service

    Comment

    • Tvbob
      tvbob
      • Dec 2009
      • 204

      #3
      Re: LG 50PC1D Recurring Ysus Buffer Short

      Change the board The FET is being turned on too long or it is working in to an abnormal load that you won't find with a volt meter.

      Comment

      Related Topics

      Collapse

      • DynaxSC
        Extreme High Current & Low Voltage Short Killer ??
        by DynaxSC
        Hi Folks

        I'm looking for a extreme high current short killer solution for a reasonable cost.

        I have an LGA1700 motherboard (ASUS PRIME Z790-P WiFi) where I exchanged the LGA socket already 3 times, and every time after the socket exchange I get a short of power supply lines VCORE (V variable) and VCCIN_AUX (1.8V).
        After taking off the socket, the shorts dissappear again.
        The soldermask on the socket is already partially demaged from the heat, so I have reconstructed the soldermask by manually painting the missing soldermask parts with a very small top of a...
        10-15-2024, 10:13 AM
      • PlasMatt
        LG 60PV450 Possible Bad YSUS Need help confirming Diagnosis
        by PlasMatt
        I have an LG plasma that after reading through a bunch of posts and doing some testing I believe has a bad YSUS board. The problem is that that doesn't make sense to me for some of the symptoms. The problem started yesterday. While watching a movie the TV just shut down like I pressed power. I have it hooked to a PC and use RS232 to turn it off and on so I thought maybe something had glitched there. I turned it back on and finished the movie with no problems. The same thing happened today so I checked logs to see if something in the control glitched and sent an off command but it didn't, After...
        09-20-2025, 06:50 PM
      • Stephen
        MacBook Pro 14" A2442 Short on PPBUS_AON but no short present when injecting voltage!
        by Stephen
        I check PPBUS_AON and there is a short present on the line, the computer shows a short when testing for short to ground, so when I inject voltage into the line, I get 0AMPS so no short is showing up. I have replaced a blown cap on this board that exploded and tested for the short and it is now removed. Any suggestions? I tested voltage at the line when the fuses are connected and I am getting 1.2 Volts at the line.
        02-06-2025, 12:03 PM
      • howardc64
        A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
        by howardc64
        Problem

        This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
        08-04-2024, 10:36 PM
      • adelfr2009
        HP Victus 15-fb dag3pamb8d0 Short on VCORE – How to Confirm CPU Fault?
        by adelfr2009
        I have a laptop HP Victus 15-fb with motherboard DAG3PRMB8D0, CPU Ryzen 7535HS, and GPU RTX 2050. The laptop has a power issue: it does not turn on at all, and there is no light on the DC jack.
        After inspection, I found that an NMOS near the charger input had a short. I replaced it, but the short remained on the 19V line. I checked the charging circuit and it was fine, but the short appears after the current sense resistor near the charger. The charger does not pass current when connected, so I inject 3V–4V after the sense resistor. No component gets hot, except the CPU which becomes...
        09-28-2025, 10:21 PM
      • Loading...
      • No more items.
      Working...