No picture on 58" plasma TV

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • vikasintl
    New Member
    • Oct 2013
    • 5
    • USA
    #1

    No picture on 58" plasma TV

    TV model no. is TH-58PE75U ..it has no picture...few minutes after powering it on, the led starts blinking and it blinks for about 13 times ....I found Factory service manual and it says

    Communication error with IC8001(Pesks lite 2)
    and check board A and board part no. is TNPH0692ADS Or TNPH0692(1)A

    So I concluded that ...we need to replace A board....

    ....but..am not tech at all...I just read the manual and concluded that I should replace board......but before I buy the board and replace it...

    I would like an advice on if replacing board is really necessary or something else can cause this 13 blinks? what else I should look for?

    Just replacing board will solve the problem? or it will solve temporarily and problem will start again?


    PLEASE advice as am nieve and dont have money to pay the shop to fix it..

    Also where can I buy this board in case I need to replace it?
    Tags: None
    • freakaftr8
      Badcaps Legend
      • Oct 2012
      • 3743
      • USA
      #2
      Re: No picture on 58" plasma TV

      These a boards are known issues in this model.
      Did I leave the soldering iron on?

        Comment

        • vikasintl
          New Member
          • Oct 2013
          • 5
          • USA
          #3
          Re: No picture on 58" plasma TV

          Originally posted by freakaftr8
          These a boards are known issues in this model.
          OK...so you in indirectly saying replace the board...
          Where... Can I buy a replacement?

            Comment

            Previous template Next

            Related Topics

            Collapse
            • m1ch43lzm
              HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
              by m1ch43lzm
              Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
              Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
              05-12-2025, 08:37 PM
            • howardc64
              TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
              by howardc64
              All left and right refers to looking from rear of TV (or looking from front with TV upside down)
              • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
              • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
              ...
              07-24-2025, 05:17 PM
            • r-p
              Maldischarge-link that fixes it with replacing caps
              by r-p
              Starting this thread because Capkid doesn't seem to be reprogramming controlboards anymore (LG 60PZ950 with red maldischarge) and my game-plasma also has maldischarge (Hitachi 42PD3200). So I will grasp at straws to keep them running. I am extremely bad at throwing stuff away.

              Is there any merit to this link?

              Very short version: Specific caps seem to loose their capacitance and/or increase their ESR. This may cause the maldischarge. Replace them with better/bigger/newer ones and problem solved.

              From the limited knowledge I have on the subject, I think...
              01-21-2020, 05:16 PM
            • stecos
              Panasonic Plasma main board repair (ST30 GT30 VT30 ST50 GT50 VT50),LED with 3 blincks
              by stecos
              Hi everyone!
              I happened several times, in the search for help from the web, to consult this very interesting forum.
              So I decided to sign up and I intend to participate actively by making available my knowledge and experience on the subject, I'm a new user but at the same time I'm old in the sense that I have 4 decades of experience in repairing and designing electronics but above all I'm a great passionate about the subject.

              Having said that I come to the gist of my post on the forum as the title suggests.
              For my passion for technology I'm now collecting several...
              11-28-2022, 11:39 AM
            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              ORIGINAL POWER SUPPLY BOARD
              7 Photos
              11-22-2024, 01:46 PM
            • Loading...
            • No more items.
            Working...