Panasonic 55vt30 board replacement

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • Moreno83
    Badcaps Legend
    • Jun 2014
    • 2008
    • The Netherlands
    #21
    Re: Panasonic 55vt30 board replacement

    You need to find out if the buffers are shorted or just the ysus board.
    Repair kit is good but you will never know if you get real parts....
    I only repair Panasonic plasma tv's! Currently owning a TX-P55VT50 and still searching for a ZT60!

      Comment

      • bektafig
        Member
        • Sep 2016
        • 10
        • TURKEY
        #22
        Re: Panasonic 55vt30 board replacement

        Originally posted by Moreno83
        You need to find out if the buffers are shorted or just the ysus board.
        Repair kit is good but you will never know if you get real parts....
        how can I learn. 7 gives the signal, but times?

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • sam_sam_sam
            Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
            by sam_sam_sam
            I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

            This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

            After all of...
            07-13-2024, 08:14 PM
          • canadaboy25
            Panasonic TC-P54VT25 No image. A or D board?
            by canadaboy25
            I have a Panasonic TC-P54VT25 that will power on and prime the display but there is no image at all.

            The panel is primed as there is a slight glow from the entire panel. This means the problem should be logic related. The service manual also confirms this and recommends replacing the A or the D board.

            I have tried to get the TV to display the test sequence but I have been unable to and I don't even know if this TV has a test sequence or not. I tried following tom66's instructions in post #3 on this thread https://www.badcaps.net/forum/showthread.php?t=26790. There was...
            01-17-2021, 01:06 AM
          • Tynan Dill
            Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
            by Tynan Dill
            I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

            Upon bringing it home and plugging it up, it showed a standby light.

            I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

            The screen seems to blackout and stay black, but with a flashlight I can see the display.

            With my Playstation 4 connected via HDMI, and running a game I can hear sound.

            Assuming...
            ORIGINAL POWER SUPPLY BOARD
            7 Photos
            11-22-2024, 01:46 PM
          • howardc64
            A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
            by howardc64
            Problem

            This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
            08-04-2024, 10:36 PM
          • boosti45
            Macbook pro logic board replacement parts quesion
            by boosti45
            i have a 2020 macbook pro 13" A2251 with 820-09149 logic board so i found an issue with chip labeled U6903 according to schem. boardview using flexBV software, so i removed it from the board and the issue im having is that the chip says "07A08FI ELC180​" on top of it but when searching for a replacement chip, i can find tons of identical looking chips that also have "ELC180" printed on them but the first set of digits is never the same so im trying to find out if i need this exact chip with these same numbers as mine and if not which ones are compatible as a replacement?...
            08-21-2024, 05:23 AM
          • Loading...
          • No more items.
          Working...