-
-
Re: technika 42 lcd 910 power probs
Which ones do you have? Brand and series? Seriously, most capacitors are NOT suitable.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: technika 42 lcd 910 power probs
Capxon are really poor capacitors.... I've replaced more of them than any other...Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: technika 42 lcd 910 power probs
They are very good, but you can get a lot of fakes if you buy from shady shops, let us know the series (e.g. ZLH, YXF, MCZ) before replacing them as we need to know if they are low esr (not all Rubycon caps are.)Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: technika 42 lcd 910 power probs
would increasing the microfarad on the replacements cause a issue i.e going from 470 to 1500 same voltage tho ?Comment
-
Re: technika 42 lcd 910 power probs
Yes, almost certainly. And, MCZ are not suitable for TV PSU.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: technika 42 lcd 910 power probs
We can check the output rails and main board.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: technika 42 lcd 910 power probs
ok i been testing and checking components , i found a 4.7Mohm resister open circult which i replaced has resolved the buzzing issues from power supply, still remains in standby, i just been testing Mosfets on invertor and found n channel bottom 4 are at fault model fdd8447l 40v , iam right in saying they operate similar to diodes back to back and only allow current one way through ?Comment
-
-
Re: technika 42 lcd 910 power probs
That is stolen verbatim from 4QD.
http://www.4qd.co.uk/serv/MOSFETfail.html
http://www.4qdtec.com/mostest.htmlPlease do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: technika 42 lcd 910 power probs
In circuit is usually OK, once a suspicious device is located, remove it from the circuit and test out of circuit.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Hello all,
I'm stumped on this guy, so wanted to see if anyone has any further ideas:
Intro:
This is an Acer Nitro 5 AN515-55-55M1 with unknown prior history (bought "as-is" on eBay). It charges the battery and powers on from both AC adapter and battery, so I think this rules out main power issues.
Upon attempt to boot, it will "reboot" (meaning powers down and then powers on again) only once, and then stays stuck in a status of lights on / no post / no monitor. Powering on with fn+esc maxes out the fans on first boot attempt,... -
Powers on as normal shows an image then powers off after 10 seconds
I have to unplug it from the wall and replug to get it to turn back on but then shuts off
No blown caps
I searched for this model but nothing comes up...11-29-2024, 11:21 PM -
Hi,
I am new to this forum and have searched for some answers with problems similar to mine.
Philips TV powers on as normal for about a minute or less then click and no power at all not even standby light. If i disconnect from mains and reconnect it will power on again but for a shorter time. Once i leave it disconnected from main for a longer time it will power on for a longer period the next time.
It sounds like a power supply issue?
I have the board out and want to run some tests. Not sure what i should be doing but i put a 1k resistor across SB and +5v... -
Laptop Model: DELL Precision 3520 Motherboard: CDP80 LA-E152P Rev 1.0 (A00)
Issue: The laptop powers on automatically after being shut down.
Actions Taken by Technician:
BIOS reflashed
Intel ME region cleared
Result: Issue still persists
Additional Observations:
Power button reads 3.3V (normal)
The problem occurs both when running on battery and when connected to AC adapter... -
I replaced the backlights all good. Two months later set was dead, had a shorted D9100, replaced all good again.
Now months later set powers up,backlights light ok,no picture. 12volts missing from fuse on tcon. 12VA on power
supply is 19 volts. Changed D9100 again, same, 12 volts measures 19. Am I looking at a power supply or mainboard
issue. Set will power up with remote but not power off....
Comment