Samsung 50" plasma blank screen

[Tweek4]

Re: Samsung 50" plasma blank screen

Ah- I see it
F2000 5A.
Guess my eyes aren't as good as they used to be.

[Tweek4]

Re: Samsung 50" plasma blank screen

Attachment to post #11

[tom66]

Re: Samsung 50" plasma blank screen

There is no fuse.
I can get a good used board for $40(refundable less $15).
How good a gambler are you?

There is a fuse. It might not look like a standard fuse. Post a picture of that board.

I don't gamble, I like to verify a board is at fault first.

[Tweek4]

Re: Samsung 50" plasma blank screen

There is no fuse.
I can get a good used board for $40(refundable less $15).
How good a gambler are you?

[tom66]

Re: Samsung 50" plasma blank screen

It looks like there is a fuse on the main logic board; check if this is okay.

[tom66]

Re: Samsung 50" plasma blank screen

Yep, probably.

[Tweek4]

Re: Samsung 50" plasma blank screen

See post 4. PlainBill calls it the main logic board.
That one?

[tom66]

Re: Samsung 50" plasma blank screen

Is that the same as the Logic-Main board?
I'll start a thread for the Panasonic.
Thanks
Peter

No, it's the board that connects the main board, sustains and X drivers together.

[Tweek4]

Re: Samsung 50" plasma blank screen

Is that the same as the Logic-Main board?
I'll start a thread for the Panasonic.
Thanks
Peter

[tom66]

Re: Samsung 50" plasma blank screen

Well, I'm going to place a bet on the plasma control board being at fault, because you have sound and the startup chime. But I can't be certain.

Start a thread for the Panasonic.

[Tweek4]

Re: Samsung 50" plasma blank screen

It would be rather nice to determine the cause. Strangely enough, we have been having startup problems with a Panasonic rear projection (and still are) and the Samsung,having been barely used and very reliable was being moved to replace it. It would be good to get one of them fixed.
Peter

[tom66]

Re: Samsung 50" plasma blank screen

That's good. That means the screen itself is probably good.

[Tweek4]

Re: Samsung 50" plasma blank screen

Yes. There are two flickers of light when I power on.
The screen has low level grey glow in dark room. Not noticeable in daylight.

[tom66]

Re: Samsung 50" plasma blank screen

Do you get any light from the screen at all? YYou might need to turn all the lights out and close the curtains as it can be very faint on some plasma displays.

[Tweek4]

Re: Samsung 50" plasma blank screen

For the heck of it, I measured the heat sink temps after 15 minutes of run time.
They were all warm, from 112F on the PS to 102F and 94F on the Y and X(Z) boards.

[Tweek4]

Re: Samsung 50" plasma blank screen

Stock screws were used - I thought the same thing initially but on examining the stand bracket inside the tv - plenty of clearance.

[kc8adu]

Re: Samsung 50" plasma blank screen

if it worked fine till you reattached the stand is it possible you used the wrong bolts to put the stand on?iirc i saw this on a westinghouse.too long of bolts damaged a board.

[Tweek4]

Re: Samsung 50" plasma blank screen

Tom66...
Is the buzzing normal?
I disconnected each buffer in turn and saw no change.
Grasping at straws.
Peter

[Tweek4]

Re: Samsung 50" plasma blank screen

Hi tom66....
Yes - both boards-seems to emanate from the centre of the large heat sink on the left board. Hard to discern on the right board. Both very faint and slightly different pitch.
Peter

[tom66]

Re: Samsung 50" plasma blank screen

Do you hear a faint buzzing sound from either board on the left or right of the TV while in operation?