Toshiba 37CV510U Backlight

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 97wing
    Member
    • Oct 2010
    • 15

    #1

    Toshiba 37CV510U Backlight

    A year ago I worked on this tv and the inverter board had obvious damage to an IC chip and two bloated caps. I went ahead and bought another board instead of trying to change the tiny smd IC. It had been working fine.

    Today, I get the tv back. The symptoms are: when you turn the tv on, the screen will flash on then off ( you can see words), flash on then off ( you can see words) then go black. The power light stays green. After about a minute, it will power down.

    I looked at the black screen with a flashlight, and I can see the words, so I feel I have another inverter problem.

    I removed the inverter to see no obvious defects.

    If it is an inverter problem, why does the tv power down after a minute?
  • PlainBill
    Badcaps Legend
    • Feb 2009
    • 7034
    • USA

    #2
    Re: Toshiba 37CV510U Backlight

    Originally posted by 97wing
    A year ago I worked on this tv and the inverter board had obvious damage to an IC chip and two bloated caps. I went ahead and bought another board instead of trying to change the tiny smd IC. It had been working fine.

    Today, I get the tv back. The symptoms are: when you turn the tv on, the screen will flash on then off ( you can see words), flash on then off ( you can see words) then go black. The power light stays green. After about a minute, it will power down.

    I looked at the black screen with a flashlight, and I can see the words, so I feel I have another inverter problem.

    I removed the inverter to see no obvious defects.

    If it is an inverter problem, why does the tv power down after a minute?
    Because the inverter sends a status signal to the main board. Aft er the inverter shuts down twice the main board shuts the TV down.

    Of course, this is pure speculation; you didn't bother to supply any pictures, I didn't bother to give the problem much thought.

    PlainBill
    For a number of reasons, both health and personal, I will no longer be active on this board. Any PMs asking for assistance will be ignored.

    Never be afraid to try something new. Remember, amateurs built the ark. Professionals built the Titanic.

    Comment

    Related Topics

    Collapse

    • triplefour
      UN65TU700DF picture and sound but no backlight. BL tests ok but repl. PSU didnt fix!
      by triplefour
      this tv is throwing me for a loop. do samsung tvs no longer have the backlight self test feature built into the power supply?
      i tested the backlight with my LED tester and it lights up both strips. one of them reads 100v and the other reads 63.7v.
      unplugged mainboard from power supply but left backlight plugged in, and then plugged psu wall power in. expected to see backlights light up but see nothing.
      according to how ive diagnosed in the past, this would almost always be a bad power supply. replacement power supply was cheap like 20$ from ebay. but still i get not even...
      09-13-2023, 10:43 PM
    • Boyxba
      TOSHIBA BACKLIGHT MAINBOARD C55-a-1h9
      by Boyxba
      I have a toshiba laptop satelite series c55-a-1h9 with a burnt item on pcb motherboard which is responsible for backlight display. the short came after installation of cable lvds and broken the leg with the v+ of backlight and made this short . the lvds cable replaced and i have working display now but not backlight. the problem is i dont know what was the component that burned in order to change it. voltage i have in this points of burned item at up side 19v and dropping and from down i have steady 19v . can anyone help me? i shall post some photos to see....
      05-13-2023, 11:47 AM
    • DanPoka
      Guide me through repairing a Dell p2210f LCD ccfl backlight monitor
      by DanPoka
      I bought this p2210f dell monitor to fix. Schematic is the same as p2210.
      Behaviour is that monitors comes on but then backlight switches off almost instantly. If I look with flashlight I can still find the "No signal message". So definitely a backlight issue. Trying to advance the issue I proved that the protection circuit is switching off the backlight by shorting out C3 and resistor to disable the INL chip then re enable by removing the short.
      This is where it gets interesting. When I disassembled the monitor to solder leads on c3 capacitor I noticed the backlight flickered...
      02-15-2025, 05:05 AM
    • Comp_Pro
      No Backlight Macbook A1990 820-01041
      by Comp_Pro
      Hello all,

      Am trying to figure out this backlight issue with this A1990 Macbook Pro.

      Tests performed:

      There is no backlight even with a good screen.
      Backlight IC is receiving the correct support voltages.
      Fuse F8400 ok
      Current sense resistor R8400 ok
      Backlight IC is receiving 3.3V on enable pin.
      Backlight IC receiving voltage from PPBUS_G3H, aprox 12.5V.
      Backlight IC receiving 5V from PP5V_G3S
      Backlight IC BKLT_SCL and BKLT_SDA both measure 0.545V diode mode to ground
      I2C_BKLT_SCL and I2C_BKLT_SDA both measure...
      05-06-2024, 10:23 PM
    • willis6732
      Toshiba 55lf621c21 Dim Picture / Backlight afterbypassing a Burnt LED
      by willis6732
      Hello,

      This TV came in for a backlight Repair. I bypassed the Burnt LED as shown in Picture. I thought it was fixed and returned to customer. So I dont have the TV anymore, but customer says its not really watchable.

      Now the TV Is much dimmer than before. It does a quick bright flash when it first turns on.

      The Driver board looked pretty toasty in the LED Driver Area.

      So I am wondering.. how can i Tell if this is a LED or Driver Board Issue?...
      12-17-2024, 04:09 PM
    • Loading...
    • No more items.
    Working...